Abstract
The recent discovery of memristor has sparked renewed interest in the scientific community about state dependent resistances. In the current paper, we show that the detector used in the first radios, called cat’s whisker, had memristive properties. We have identified the state variable governing the resistance state of the device and can program it to switch between multiple stable resistance states. Our observations are valid for a larger class of devices called coherers, including cat’s whisker. We further argue that these constitute the missing canonical physical implementations for a memristor.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Notes
- 1.
- 2.
Philmore 7003 cat’s whisker is easily available from various antique radio or radio hobbyists shops and can also be ordered online through sites like eBay. On the other hand, it is easy to build it oneself using one of the semiconducting crystals and a metallic wire.
- 3.
Hotspots are found by the following process. The device is either connected to an oscilloscope or a radio receiver circuit. Then the point of contact between the crystal and wire is changed till a diode-like characteristics is observed. The point(s) on the crystal where rectification is observed are hotspots. Finding hotspots is generally a time consuming task for non-experts [14].
- 4.
These values may change according to the metal, the contact, pressure, etc.
- 5.
Note that the non-linear DC resistance changes appreciably only when the maximum current through the device has changed. This can be seen through color correspondence, where each color shows a new stable non-linear DC resistance-state and the transitions are marked by the first pulse of higher amplitude: P1, P2 and P3 being the time interval where these pulses are applied. In case the maximum current passed through the device does not change, the non-linear DC resistance feebly oscillates around the same value, as seen in the time-interval of A1, A2 and A3. Furthermore, we have observed that the non-linear DC resistance remains fixed even when the amplitude of the pulse is decreased, since the maximum current has not changed.
- 6.
Whereas triangle current pulse is symmetrical with respect to center axis shown in Fig. 9, voltage response during that time interval is not symmetrical. This causes hysteresis loop. We refer to different stable V–I characteristics as different states of the device.
- 7.
It is evident by looking at regions depicted by A0 to A6 that the change in resistance happens at the first pulse of the transition. One may also note that these observations show recovery of resistance to a higher non-linear DC resistance: A4 resistance is higher than A5 resistance.
References
Adhikari, S.P., Sah, M.P., Kim, H., Chua, L.O.: IEEE Trans. Circuits Syst. I (2013). doi:10.1109/TCSI.2013.2256171
Bondyopadhyay, P.: Proc. IEEE 86(1), 259 (1998)
Bose, J.: Proc. R. Soc. Lond. 65(413–422), 166 (1899)
Bose, J.: Originally presented to the British Association at Glasgow, September 1901
Bose, J.: Patent USA 755, 840 (1904)
Chua, L.: IEEE Trans. Circuit Theory 18(5), 507 (1971)
Chua, L.: Proc. IEEE 91(11), 1830 (2003)
Chua, L.: Appl. Phys. A, Mater. Sci. Process. 102(4), 765 (2011)
Chua, L.O.: Proc. IEEE 100(6), 1920 (2012)
Chua, L.: Nanotechnology 24(38), 3001 (2013)
Chua, L., Kang, S.: Proc. IEEE 64(2), 209 (1976)
Dilhac, J.: IEEE Commun. Mag. 47(9), 20 (2009)
Falcon, E., Castaing, B.: Invest. Cienc. 404, 80 (2010)
Fleming, J.: In: The Principles of Electric Wave Telegraphy, New York (1908)
Gandhi, G., Aggarwal, V.: mLabs report (2010). www.mlabs.in
Jo, S., Lu, W.: Nano Lett. 8(2), 392 (2008)
Kim, T., Jang, E., Lee, N., Choi, D., Lee, K., Jang, J., Choi, J., Moon, S., Cheon, J.: Nano Lett. 9(6), 2229 (2009)
Kim, K., Jo, S., Gaba, S., Lu, W.: Appl. Phys. Lett. 96 (2010)
Lodge, O.: The Electrician 40, 86 (1897)
Pershin, Y., Ventra, M.: IEEE Circuits Syst. Mag. 12(1), 64 (2011)
Prodromakis, T., Toumazou, C., Chua, L.: Nat. Mater. 11(6), 478 (2012)
Strukov, D., Snider, G., Stewart, D., Williams, R.: Nature 453(7191), 80 (2008)
Acknowledgements
This paper is supported in part by AFOSR grant no. FA9550-10-1-0290 and mLabs.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Appendix
Appendix
1.1 5.1 Detailed Method to Find Average Resistance
Refer to Fig. 12 (a reproduction of Fig. 10). Here we will describe how to calculate the average resistance for the given curve during the time interval A1 for current range I 1 (0.1 mA) to I n (3.5 mA).
For input current I 1, at point P 1, the voltage is V 1. Here, the non-linear DC resistance is r 1 (V 1/I 1), the inverse of the slope of the line segment joining P 1 to origin. Similarly, at current In, the non-linear DC resistance is r n . For any current between I 1 and I n , the non-linear DC resistance is similarly defined, as shown in the figure.
To calculate the average resistance, the non-linear DC resistance is measured at regular time interval starting from point P 1 to P n . The average of these values is the average resistance. Mathematically this is equivalent to:
here t i =t p1+time interval∗(i−1).
Rights and permissions
Copyright information
© 2014 Springer International Publishing Switzerland
About this chapter
Cite this chapter
Gandhi, G., Aggarwal, V., Chua, L.O. (2014). The Detectors Used in the First Radios Were Memristors. In: Adamatzky, A., Chua, L. (eds) Memristor Networks. Springer, Cham. https://doi.org/10.1007/978-3-319-02630-5_4
Download citation
DOI: https://doi.org/10.1007/978-3-319-02630-5_4
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-02629-9
Online ISBN: 978-3-319-02630-5
eBook Packages: Computer ScienceComputer Science (R0)