Abstract
The advent of small-scale testing procedures coupled with scanning electron microscopy (SEM) imaging allow for high-resolution digital image correlation (DIC) studies to examine strain localization at the grain size length scale. A systematic study was performed to determine how speckle patterning parameters (speckle density and shape) affect strain resolution of DIC using SEM imaging. Strain resolution increased with increased speckle density from 23 to 58 % area fraction. Patterns with less than 23 % area fraction exhibited significant signal noise, and a loss in strain resolution due to inadequate correlation. It was also observed that when the edges of square speckles were aligned with SEM rastering directions, the noise in the e yy data was double the noise in the e xx data. Rotating the speckle to eliminate edge alignment with the rastering direction significantly decreased the e yy strain noise. Competing optimization requirements for the correlation parameters were needed to minimize strain intensity noise or maximize spatial resolution. Application of the optimization techniques to high temperature in-situ studies of Ni-based superalloys will also be presented.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Tong W (1997) Detection of plastic deformation patterns in a binary aluminum alloy. Exp Mech 37(4):452–459
Read D, Cheng Y, Keller R, McColskey DJ (2001) Tensile properties of free-standing aluminum thin films. Scripta Materialia 45(5):583–589
Carroll J, Abuzaid W, Lambros J, Sehitoglu H (2010) An experimental methodology to relate local strain to microstructural texture. Rev Sci Instruments 81(8):083703–083703–9
Efstathiou C, Sehitoglu H, Lambros J (2010) Multiscale strain measurements of plastically deforming polycrystalline titanium: role of deformation heterogeneities. Int J Plast 26:93–106
Kim K, Daly S (2010) Martensite strain memory in the shape memory alloy nickel-titanium under mechanical cycling. Exp Mech 51:641–652
Sutton MA, Li N, Joy DC, Reynolds AP, Li X (2007) Scanning electron microscopy for quantitative small and large deformation measurements part i: SEM imaging at magnifications from 200 to 10,000. Exp Mech 47:775–787
Sutton MA, Li N, Garcia D, Cornille N, Orteu JJ, McNeill SR, Schreier HW, Li X, Reynolds AP (2007) Scanning electron microscopy for quantitative small and large deformation measurements part II: experimental validation for magnifications from 200 to 10,000. Exp Mech 47:789–804
Tschopp M, Bartha B, Porter W, Murray P, Fairchild S (2009) Microstructure-dependent local strain behavior in polycrystals through in-situ scanning electron microscope tensile experiments. Metallurgical Mater Trans A 40:2363–2368
Biery N, de Graef M, Pollock TM (2003) A method for measuring microstructural-scale strains using a scanning electron microscope: applications to gamma-titanium aluminides. Metallurgical Mater Trans A 34(10):2301–2313
Jin H, Haldar S, Bruck HA, Lu W-Y (2011) Grid method for microscale discontinuous deformation measurement. Exp Mech 51:565–574
Scrivens WA, Luo Y, Sutton MA, Collette SA, Myrick ML, Miney P, Colavita PE, Reynolds AP, Li X (2006) Development of patterns for digital image correlation measurements at reduced length scales. Exp Mech 47:63–77
Kammers AD, Daly S (2013) Digital image correlation under scanning electron microscopy: methodology and validation. Exp Mech 53(9):1743–1761
Walley JL, Wheeler R, Uchic MD, Mills MJ (2012) In-situ mechanical testing for characterizing strain localization during deformation at elevated temperatures. Exp Mech 52(4):405–416
Langdon T (2006) Grain boundary sliding revisited: developments in sliding over four decades. J Mater Sci 41:597–609
Sutton M, Orteu J, Schreier H (2009) Image correlation for shape, motion and deformation measurements basic concepts, theory and applications. Springer, New York
C. Solutions, VIC-2D testing guide (2009)
Carter J, Zhou N, Sosa J, Shade P, Pilchak A, Kuper M, Wang Y, Fraser H, Uchic M, Mills M (2012) Characterization of strain accumulation at grain boundaries of nickel-based superalloys. In: Superalloys 2012 (Warendale). TMS, pp 43–52
Acknowledgements
Funding was provided by the Air Force Research Laboratory (AFRL) STW-21 program FA9550-09-1-0014. The authors would like to thank Aimee Price, Research Associate of the Institute for Materials Research at The Ohio State University for the assistance in producing the patterns used for this study.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2015 The Society for Experimental Mechanics, Inc.
About this paper
Cite this paper
Carter, J.L.W., Uchic, M.D., Mills, M.J. (2015). Impact of Speckle Pattern Parameters on DIC Strain Resolution Calculated from In-situ SEM Experiments. In: Carroll, J., Daly, S. (eds) Fracture, Fatigue, Failure, and Damage Evolution, Volume 5. Conference Proceedings of the Society for Experimental Mechanics Series. Springer, Cham. https://doi.org/10.1007/978-3-319-06977-7_16
Download citation
DOI: https://doi.org/10.1007/978-3-319-06977-7_16
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-06976-0
Online ISBN: 978-3-319-06977-7
eBook Packages: EngineeringEngineering (R0)