Summary
Pupl quality, in terms of a fiber shape factor S and a fiber length factor L, was determined for 96 pulps disk-refined from chips of varying characteristics. S was evaluated in terms of the Canadian Standard Freeness of the 48/100 fiber length fraction and is a parameter inversely proportional to specific surface. L is the percentage, by weight, of pulp retained on a 48-mesh screen and reflects the distribution by weight of fiber length in the whole pulp. S and L accounted for as much as 83 percent of the variation in handsheet properties. Properties were improved by using pulps displaying low values of S and relatively high values of L. Both S and L were related to specific refining energy and wood quality. S increased with increasing unextracted chip specific gravity and rings per inch of growth rate but decreased with increasing latewood content and refining energy. L decreased with increasing refining energy, rings per inch of growth rate, and unextracted chip specific gravity but increased with increasing latewood.
Zusammenfassung
Die Qualität von 96 verschiedenen Zellstoffarten, alle im Scheiben-Refiner aus Hackschnitzeln unterschiedlicher Art hergestellt, wurde mit Hilfe des Faser-Form-Faktors S und des Faser-Längen-Faktors L bestimmt. S wurde in Einheiten des Mahlgrades nach Canadian Standard Freeness der 48/100 Faser-Längen-Fraktion bestimmt. S ist als Parameter umgekehrt proportional zur spezifischen Oberfläche. L ist der gewichtsmäßig bestimmte Anteil an Zellstoff, der ein 48-Mesh-Sieb nicht mehr passiert und gibt gleichzeitig gewichtsmäßig die Verteilung der Faserlängen in der Gesamtmenge des Zellstoffes an. Durch S und L werden 83% der Eigenschaftsschwankungen innerhalb der Prüfblätter erklärt. Diese Eigenschaften konnten durch Zellstoff mit niedrigeren S-Werten und relativ hohen L-Werten verbessert werden. Sowohl S als auch L wurden mit der spezifischen Refiner-Leistung und mit der Holzqualität korreliert. S nahm mit ansteigender Dichte der unbehandelten Hackschnitzel und mit ansteigender Jahrringzahl je Zuwachseinheit zu, fiel dagegen mit ansteigendem Spätholzanteil und Refiner-Leistung ab. Dagegen nahm L mit ansteigender Refinerleistung, Jahrringzahl je Zuwachseinheit und Dichte der unbehandelten Hackschnitzel ab, stieg jedoch mit zunehmendem Spätholzanteil an.
Similar content being viewed by others
References
Forgacs, O.: The Characterization of Mechanical Pulps. Pulp Pap. Mag. Can. 64 (1963) No. C; T89-T118.
McMillin, C. W.: Chemical Composition of Loblolly Pine Wood as Related to Specific Gravity, Growth Rate, and Distance from Pith. Wood Sci. Technol. 2 (1968a) No. 4; 233–240.
—: Gross Wood Characteristics Affecting Properties of Handsheets Made from Loblolly Pine Refiner Groundwood. TAPPI 51 (1968b) 51–56
—: Morphological Characteristics of Loblolly Pine Wood as Related to Specific Gravity, Growth Rate, and Distance from Pith. Wood Sci. Technol. 2 (1968c) No. 3; 166–176
—: Aspects of Fiber Morphology Affecting Properties of Handsheets Made from Loblolly Pine Refiner Groundwood. Wood Sci. Technol. 3 (1969a) No. 2, 139–149
—: Wood Chemical Composition as Related to Properties of Handsheets Made from Loblolly Pine Refiner Groundwood. Wood Sci. Technol. 3 (1969b) No. 3, 232–238
Author information
Authors and Affiliations
Additional information
The author appreciatively acknowledges the assistance of Roy O. Martin Lumber Co., Alexandria, La.: R. A. Leask and J. Adams of Bauer Bros. Co., Springfield, Ohio; and D. Bower, mathematical statistician at the Southern Forest Experiment Station, New Orleans, La.
Rights and permissions
About this article
Cite this article
McMillin, C.W. Quality of refiner groundwood pulp as related to handsheet properties and gross wood characteristics. Wood Science and Technology 3, 287–300 (1969). https://doi.org/10.1007/BF00352303
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF00352303