Skip to main content
SpringerLink
Log in

Investigation of electro-discharge micro-machining of titanium super alloy

  • Original Article
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Being a difficult-to-cut material, titanium alloy suffers poor machinability for most cutting processes, especially the drilling of micro-holes using traditional machining methods. Although electrical discharge machining (EDM) is suitable for machining titanium alloys, selection of machining parameters for higher machining rate and accuracy is a challenging task in machining micro-holes. The present research attempts to optimize micro-EDM process parameters for machining Ti-6Al-4V super alloy. To verify the optimal micro-EDM process parameters settings, metal removal rate (MRR), tool-wear rate (TWR), over cut (OC) and taper were chosen as observed performance criteria. In addition, four independent parameters such as peak current, pulse-on time, flushing pressure, and duty ratio were adopted for evaluation by the Taguchi method. From the ANOVA and S/N ratio graph, the significant process parameters and the optimal combination level of machining parameters were obtained. It is seen that machining performances are affected mostly by the peak current and pulse-on time during micro-electro-discharge machining of titanium alloy. Mathematical models have been developed to establish the relationship between various significant process parameters and micro-EDM performance criteria. In-depth studies have also been made to examine the influence of various process parameters on the white layer and surface topography through SEM micrographs of machined micro-hole.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Lin YC, Yan BH, Chang YS (2000) Machining characteristics of titanium alloy (Ti-6Al-4V) using a combination process of EDM with USM. J Mater Process Technol 104(3):171–177 DOI 10.1016/S0924–0136(00)00539–2

    Article  Google Scholar 

  2. Singh R, Khamba JS (2006) Ultrasonic machining of titanium and its alloys: a review. J Mater Process Technol 173(2):125–135 DOI 10.1016/j.jmatprotec.2005.10.027

    Article  Google Scholar 

  3. Kaminski PC, Capuano MN (2003) Micro hole machining by conventional penetration electrical discharge machine. Int J Mach Tools Manuf 43(11):1143–1149 DOI 10.1016/S0890–6955(03)00124–X

    Article  Google Scholar 

  4. Masanta M, Pradhan BB, Sarkar BR, Bhattacharyya B (2005) Study on the influence of micro EDM process parameters. Proceedings of 4th COPEN (2005), Jadavpur University, Kolkata, pp 269–275

  5. Pham DT, Dimov SS, Bigot S, Ivanov A, Popov K (2004) Micro–EDM: recent developments and research issues. J Mater Process Technol 149(1–3):50–57 DOI 10.1016/j.jmatprotec.2004.02.008

    Article  Google Scholar 

  6. Lim HS, Wong YS, Rahman M, Lee MK (2003) A study on the machining of high-aspect ratio micro-structures using micro-EDM. J Mater Process Technol 140(1–3):318–325 DOI 10.1016/S0924–0136(03)00760–X

    Article  Google Scholar 

  7. Zhao W, Wang Z, Di S, Chi G, Wei H (2002) Ultrasonic and electric discharge machining to deep and small holes on titanium alloys. J Mater Process Technol 120:101–106 DOI 10.1016/S0924–0136(01)01149–9

    Article  Google Scholar 

  8. Bigot S, Ivanov A, Popov K (2005) A study of the micro-EDM electrode wear. Proceedings of the First International Conference on the Multi- Material Micro Manufacture, 4M, pp 355–358

  9. Pham DT, Ivanov A, Bigot S, Popov K, Dimov S (2006) An investigation of tube and rod electrode wear in micro-EDM drilling. Int J Adv Manuf Technol DOI 10.1007/S00170–006–0639–7

  10. Narasimhan J, Yu Z, Rajurkar KP (2004) Tool wear compensation and path generation in micro and macro EDM. Trans NAMRI/SME 32:151–158

    Google Scholar 

  11. Pradhan BB, Bhattacharyya B (2008) Improvement in micro-hole machining accuracy by polarity changing technique for micro-electrode discharge machining on Ti-6Al-4V, Proc IMechE Vol.222 Part B, J Eng Manuf

  12. Han F, Wachi S, Kuneida M (2004) Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control. Precis Eng 28:378–385 DOI 10.1016/j.precisioneng.2003.11.005

    Article  Google Scholar 

  13. Liu HS, Yan BH, Chen CL, Huang FY (2006) Application of micro-EDM combined with high-frequency dither grinding to micro-hole machining. Int J Mach Tools Manuf 46:80–87 DOI 10.1016/j.ijmachtools.2005.03.017

    Article  Google Scholar 

  14. Allen DM, Almond HJA, Bhogal JS, Green AE, Logan PM, Huang XX (1999) Typical metrology of micro-hole arrays made in stainless steel foils by two-stage micro-EDM. Ann CIRP 48(1):127–130

    Article  Google Scholar 

  15. Chow HM, Yan BH, Huang FY, Hung JC (2000) Study of added powder in kerosene for micro-slit machining of titanium alloy using electro-discharge machining. J Mater Process Technol 101:95–103 DOI 10.1016/S0924–0136(99)00458–6

    Article  Google Scholar 

  16. Bhattacharyya B, Gangopadhyay S, Sarkar BR (2007) Modelling and analysis of EDMed job surface integrity. J Mater Process Technol 189:169–177 DOI 10.1016/j.jmatprotec.2007.01.018

    Article  Google Scholar 

  17. Tsai YY, Masuzawa T (2004) An index to evaluate the wear resistance of the electrode in micro-EDM. J Mater Process Technol 149(1–3):304–309 DOI 10.1016/j.jmatprotec.2004.02.043

    Article  Google Scholar 

  18. Greenwood NN, Earnshaw A (2005) Chemistry of elements, 2nd edn. Elsevier, Amsterdam, pp 299, 813, 814

  19. Phadke MS (1989) Quality engineering using robust design. Prentice Hall, Englewood Cliffs, NJ

    Google Scholar 

  20. Montgomery DC (1997) Design and analysis of experiments. Willey, New York

    MATH  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Mechanical Engg. Deptt., SMIT, Majitar, Sikkim

    B. B. Pradhan

  2. Production Engineering Department, Jadavpur University, Kolkata, 700 032, India

    M. Masanta, B. R. Sarkar & B. Bhattacharyya

Authors
  1. B. B. Pradhan
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. M. Masanta
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. B. R. Sarkar
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. B. Bhattacharyya
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to B. Bhattacharyya.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Pradhan, B.B., Masanta, M., Sarkar, B.R. et al. Investigation of electro-discharge micro-machining of titanium super alloy. Int J Adv Manuf Technol 41, 1094–1106 (2009). https://doi.org/10.1007/s00170-008-1561-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-008-1561-y

Keywords

Search

Navigation