Abstract
This paper presents a model-based approach for monitoring of shape deviations for milling operations. In order to detect occurring shape deviations of the machined workpiece during the milling process, different kinds of process models are presented and discussed for their application on manufacturing quality monitoring. Thereby, a model-based system was presented for the monitoring of shape deviations based on measured cutting forces. For the transformation of cutting forces into shape deviations, a tool deflection model and material removal model were designed and applied to a monitoring system. The presented model-based monitoring approach delivers accurate quality information, like geometric shape deviations, which can be monitored against geometric tolerances, providing a quality monitoring of manufacturing processes. The reconstruction of shape deviations from measured cutting forces is verified experimentally by comparing measured and reconstructed shape contours.
Article PDF
Similar content being viewed by others
References
Teti R (1995) A review of tool condition monitoring literature. CIRP Ann Manuf Technol 44(2):659–666
Byrne G, Dornfeld D, Inasaki I, Ketteler G, König W, Teti R (1995) Tool condition monitoring (TCM)—the status of research and industrial application. CIRP Ann Manuf Technol 44(2):541–567
Klocke F, Reuber M (2000) Process monitoring in sculptured surface milling. Prod Eng Res Dev 7(1):1–4
Sarhan A, Sayed R, Nassr AA, El-Zahry RM (2001) Interrelationships between cutting force variation and tool wear in end-milling. J Mater Process Technol 109(3):229–235
Bhattacharyya P, Sengupta D (2008) Estimation of tool wear based on adaptive sensor fusion of force and power in face milling. Int J Prod Res 47(3):817–833
Brinkhaus J (2009) Statistische Verfahren zur selbstlernenden Überwachung spanender Bearbeitungen in Werkzeugmaschinen, PhD-Thesis, Leibniz Universität Hannover
Dornfeld DA, DeVries M (1990) Neural network sensor fusion for tool condition monitoring. CIRP Ann Manuf Technol 39(1):101–105
Chen J, Susanto V (2003) Fuzzy logic based in-process tool-wear monitoring system in face milling operations. Int J Adv Manuf Technol 21(3):186–192
Brezak D, Majetic D, Udiljak T, Kasac J (2012) Tool wear estimation using an analytic fuzzy classifier and support vector machines. J Intell Manuf 23(3):797–809
Cus F, Milfelner M, Balic J (2006) An intelligent system for monitoring and optimization of ball-end milling process. J Mater Process Technol 175(1–3):90–97
Saglam H, Unuvar A (2003) Tool condition monitoring in milling based on cutting forces by a neural network. Int J Prod Res 41(7):1519–1532
Uhlmann E, Fries E (1999) Intelligent process monitoring. Prod Eng Res Dev 6/2:25–28
Quintana G, Garcia-Romeu M, Ciurana J (2011) Surface roughness monitoring application based on artificial neural networks for ball-end milling operations. J Intell Manuf 22(4):607–617
Zhu R, DeVor RE, Kapoor SG (2003) A model-based monitoring and fault diagnosis methodology for free-form surface machining process. J Manuf Sci Eng 125(3):397–404
Denkena B, Krüger M, Bachrathy D, Stepan G (2012) Model based reconstruction of milled surface topography from measured cutting forces. Int J Mach Tool Manuf 54–55:25–33
Altintas Y, Yellowley I (1989) In-process detection of tool failure in milling using cutting force models. J Eng Ind 111(2):149–157
Denkena B, Köller M, Bertram O (2012) Teachless process monitoring for single part production, In: Proceedings of the 1st Joint International Symposium on System-Integrated Intelligence 2012 (SYSINT 2012), 27th–29th June 2012, Garbsen, Germany pp. 117–120
Larue A, Anselmetti B (2004) A prediction of the machining defects in flank milling. Int J Adv Manuf Technol 24(1–2):102–111
Ratchev S, Liu S, Becker AA (2005) Error compensation strategy in milling flexible thin-wall parts. J Mater Process Technol 162–163:673–681
Schmidt C (2006) Level curve based geometry representation for cutting force prediction. In: Annals of DAAAM Proceedings of the 17th International DAAAM Symposium, 8–11th November 2006 Vienna Austria, pp. 367–368
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Krüger, M., Denkena, B. A model-based approach for monitoring of shape deviations in peripheral milling. Int J Adv Manuf Technol 67, 2537–2550 (2013). https://doi.org/10.1007/s00170-012-4672-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-012-4672-4