Skip to main content
SpringerLink
Log in

Numerical and experimental investigation of thermal history, material flow and mechanical properties of friction stir welded aluminium alloy to DHP copper dissimilar joint

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Dissimilar Al-Cu joining is an emerging area of interest for both academic and industrial research. Friction stir welding being a novel solid-state joining process can overcome a number of issues raised by fusion welding of such dissimilar joint and thus good joint strength is expected. However, understanding the material flow and simultaneously the formation and control of intermetallics in friction stir welding (FSW) can only attribute good joint performance. In the present study, thermal cycle has been experimentally measured and simulated as well as simulation of thermal profile and detailed material flow behaviour have been analysed and correlated with the process response on mechanical property evaluation for different combination of parameters. Material flow behaviour and identification of intermetallics have been exclusively characterized by energy-dispersive X-ray spectroscopy (EDS) mapping and X-ray diffraction (XRD). Experimentally measured thermal cycles are found to be in a good agreement with those numerically calculated. The maximum joint strength achieved for 1000 rpm and travel speed 20 mm min−1 (86.5 % of aluminium base metal) is the optimized parameter with intermetallic (IMC) thickness of 3.6 μm for the present study.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Sun Z (1995) Joining dissimilar material combinations: materials and processes. Int J Mater Prod Technol 10:16–26

    Google Scholar 

  2. Tan CW, Jiang ZG, Li LQ, Chen YB, Chen XY (2010) Microstructural evolution and mechanical properties of dissimilar Al–Cu joints produced by friction stir welding. Mater Des 51:466–473

    Article  Google Scholar 

  3. Ouyang J, Yarrapareddy E, Kovacevic RJ (2006) Microstructural evolution in the friction stir welded 6061 aluminum alloy (T6-temper condition) to copper. Mater Process Technol 172:110–122

    Article  Google Scholar 

  4. Xue P, Ni DR, Wang D, Xiao BL, Ma ZY (2011) Effect of friction stir welding parameters on the microstructure and mechanical properties of the dissimilar Al–Cu joints. Mater Sci Eng A 528:4683–4689

    Article  Google Scholar 

  5. Galvao I, Leal RM, Loureiro A, Rodrigues DM (2010) Material flow in heterogeneous friction stir welding of aluminium and copper thin sheets. Sci Technol Weld Join 15(8):654–660

    Article  Google Scholar 

  6. Li XW, Zhang DT, Qui C, Zhang W (2012) Microstructure and mechanical properties of dissimilar pure copper/1350 aluminum alloy butt joints by friction stir welding. Trans Nonferrous Met Soc China 22:1298–1306

    Article  Google Scholar 

  7. Xue P, Xiao BL, Ni DR, Ma ZY (2010) Enhanced mechanical properties of friction stir welded dissimilar Al–Cu joint by intermetallic compounds. Mater Sci Eng A 527:5723–5727

    Article  Google Scholar 

  8. Galvao I, Oliveira JC, Loureiro A, Rodrigues DM (2011) Formation and distribution of brittle structures in friction stir welding of aluminium and copper: influence of process parameters. Sci Technol Weld Join 15(8):681–689

    Article  Google Scholar 

  9. Liu P, Shi Q, Wang W, Zhang Z (2008) Microstructure and XRD analysis of FSW joints for copper T2/aluminium 5A06 dissimilar materials. Mater Letters 62:4106–4108

    Article  Google Scholar 

  10. Genevois C, Girard M, Huneau B, Sauvage X, Racineux G (2011) Interfacial reaction during friction stir welding of Al and Cu. Metall Mater Trans A 42(8):2290–2295

    Article  Google Scholar 

  11. Esmaeili A, Besharati Givi MK, Rajani Z (2011) A metallurgical and mechanical study on dissimilar friction stir welding of aluminium 1050 to brass (CuZn30). Mater Sci Eng A 528:7093–7102

    Article  Google Scholar 

  12. Abdollah-Zadeh A, Saeid T, Sazgari B (2008) Microstructural and mechanical properties of friction stir welded aluminum/copper lap joints. J Alloys Compd 460:535–538

    Article  Google Scholar 

  13. Seidel TU, Reynolds AP (2001) Visualization of the material flow in AA2195 friction stir welds using a marker insert technique. Metall Mater Trans A 32:2879–2884

    Article  Google Scholar 

  14. Schmidt H, Hattel J (2005) A local model for the thermomechanical conditions in friction stir welding. Model Simul Mater Sci Eng 13(1):77–93

    Article  Google Scholar 

  15. Reynolds AP, Lockwood WD, Seide TU (2000) Processing property correlation in friction stir welds. Mater Sci Forum 331-337:1719–1724

    Article  Google Scholar 

  16. Nunes AC, Berristein EL, Mcclure JC (2000) A rotating plug model for friction stir welding. 81st American Society of Annual Convention Chicago IL:26-28

  17. Galvão I, Leitão C, Loureiro A, Rodrigues DM (2012) Study of the welding conditions during similar and dissimilar aluminium and copper welding based on torque sensitivity analysis. Mater Des 42:259–264

    Article  Google Scholar 

  18. Neto DM, Neto P (2013) Numerical modeling of friction stir welding process: a literature review. Int J Adv Manuf Technol 65:115–126

    Article  Google Scholar 

  19. Zimmer S, Langlois L, Laye J, Bigot R (2010) Experimental investigation of the influence of the FSW plunge processing parameters on the maximum generated force and torque Int. J Adv Manuf Technol 47:2011–2015

    Article  Google Scholar 

  20. Mehta M, Chatterjee K, De A (2013) Monitoring torque and traverse force in friction stir welding from input electrical signatures of driving motors. Sci Technol Weld Join 18(3):191–197

    Article  Google Scholar 

  21. Mehta M, Arora A, De A, Debroy T (2011) Tool geometry for friction stir welding—optimum shoulder diameter. Metall Mater Trans A 42A(9):2716–2722

    Article  Google Scholar 

  22. Arora A, De A, DebRoy T (2011) Toward optimum friction stir welding tool shoulder diameter. Scr Mater 64(1):9–12

    Article  Google Scholar 

  23. Das H, Jana SS, Pal TK, De A (2014) Numerical and experimental investigation on friction stir lap welding of aluminium to steel. Sci Technol Weld Join 19(1):69–75

    Article  Google Scholar 

  24. Akinlabi ET, Madyira DM, Akinlabi SA (2011) Effect of heat input on the electrical resistivity of dissimilar friction stir welded joints of aluminium and copper. IEEE Africon, doi: 978-1-61284-993-5/11

  25. Das H, Basak S, Das G, Pal TK (2013) Influence of energy induced from processing parameters on the mechanical properties of friction stir welded lap joint of aluminium to coated steel sheet. Int J Adv Manuf Technol 641:653–1661

    Google Scholar 

  26. Bisadi H, Tavakoli A, Sangsaraki MT, Sangsaraki KT (2013) The influences of rotational and welding speeds on microstructures and mechanical properties of friction stir welded Al5083 and commercially pure copper sheets lap joints. Mater Des 43:80–88

    Article  Google Scholar 

  27. Lienert TJ, Stellwag W Jr, Grimmett BB, Warke RW (2003) Friction stir welding studies on mild steel. Weld J 82:11–19

    Google Scholar 

  28. Guerra M, Schmidt C, Mcclure JC, Murr LE, Nunes AC (2002) Flow patterns during friction stir welding. Mater Charact 49:95–101

    Article  Google Scholar 

  29. Li Y, Murr LE, Mcclure JC (1999) Flow visualization and residual microstructures associated with the friction stir welding of 2024 aluminum to 6061 aluminum. Mater Sci Eng A 271:213–223

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Welding Technology Centre, Metallurgical and Material Engineering Department, Jadavpur University, Kolkata, 700032, India

    T. K. Bhattacharya, H. Das & T. K. Pal

  2. Mechanical Engineering Department, IIT (Indian Institute of Technology), Bombay, India

    S. S. Jana

Authors
  1. T. K. Bhattacharya
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. H. Das
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. S. Jana
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. T. K. Pal
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to T. K. Pal.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Bhattacharya, T.K., Das, H., Jana, S.S. et al. Numerical and experimental investigation of thermal history, material flow and mechanical properties of friction stir welded aluminium alloy to DHP copper dissimilar joint. Int J Adv Manuf Technol 88, 847–861 (2017). https://doi.org/10.1007/s00170-016-8820-0

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-8820-0

Keywords

Search

Navigation