Abstract
Control of welding parameters is an important factor in gas metal arc welding (GMAW) because these parameters determine the heat input, cooling conditions, and time during which the microstructure and the geometry of the weld are formed. It is therefore essential that sufficient heat is transferred to highly conductive metals like aluminum and appropriate heat input used with very sensitive metals such as stainless steel and high-strength steels or when welding dissimilar metals. The objective of this study is to identify parameters of current, voltage waveforms, and electrode feeding motion that directly contribute to improvement in metal and heat transfer conditions from the electrode to the base metals. The effects of these parameters on welded joint geometry are determined. The work critically reviews research on the effect on welded joints of control of current waveform, voltage, and the alternating electrode and analyzes the different parameters that promote forces acting during metal transfer. Experiments and case studies based on controlled waveforms are discussed. The analysis shows that in controlled short-circuit gas metal arc welding (CS-GMAW), all identified parameters contribute to control of heat input and reduction in the amount of spatter and fumes generated. Variable polarity gas metal arc welding (VP-GMAW) is found to be particularly effective for aluminum welding because of its good control of mass metal transfer and weld penetration. Mixed waveform approaches (i.e., 20 pulses/controlled short circuit) improve weldability in difficult welding positions.
Similar content being viewed by others
References
Mvola B, Kah P, Martikainen J, Suoranta R (2015) State-of-the-art of advanced gas metal arc welding processes: dissimilar metal welding. Proc Inst Mech Eng B J Eng Manuf 229(10):1694–1710
Praveen P, Yarlagadda PKDV, Kang MJ (2005) Advancements in pulse gas metal arc welding. J Mater Process Technol 164–165:1113–1119
Richardson IM, Bucknall PW, SI (1994) The influence of power source dynamics on wire melting rate in pulsed GMA welding. Weld J 73(2):32–37
Scotti A, Ponomarev V, Lucas W (2012) A scientific application oriented classification for metal transfer modes in GMA welding. J Mater Process Technol 212(6):1406–1413
Norrish J, Cuiuri D (2014) The controlled short circuit GMAW process: a tutorial. J Manuf Process 16(1):86–92
Sagues P (2010) Adaptive control techniques advance automatic welding. Weld J 89(8):26–28
Kazmaier J, Stieglbauer W, and Egerland S 2010 CMT advanced—an arc process revolution, in Sheet Metal Welding Conference XIV, Livonia
Pepe N, Quintino L, Pires I, Miranda R, Yapp D 2010 Applications of innovative variants in MIG/MAG welding, in IIW – XII – 1989 – 10, Istanbul
Stava EK (1999) New surface transfer tension process speeds pipe welding. Pipe Line Gas Ind 82(9):55–57
Kim YS, Eagar TW (1993) Analysis of metal transfer in gas metal arc welding. Weld J 72(6):269–278
Waszink JH, Graat LHJ (1983) Experimental investigation of the forces acting on a drop of weld metal. Weld J 62(4):109–116
Wu CS, Chen MA, S.K. (2004) Analysis of excited droplet oscillation and detachment in active control of metal transfer. Comput Mater Sci 31(1–2):147–154
Lesnewich A (1958) Control of melting rate and metal transfer in gas-shielded metal arc welding—part 1—control of electrode melting rate. Weld J 37(8):343–353
Mvola B, Kah P, Martikainen J, Suoranta R (2016) Dissimilar welded joints operating in sub-zero temperature environment. Int J Adv Manuf Technol 87(9–12):3619–3635. https://doi.org/10.1007/s00170-016-8711-4
Xu D, Wang L, Tan M (2004) Image processing and visual control method for arc welding robot. In: Proceedings of International Conference on Robotics and Biomimetics (ROBIO), Shenyang, China, 22–26 August 2004, pp 721–726
Smith JS, Balfour C (2005) Real time top-face vision based control of weld pool size. Int J Ind Robot 32(4):334–340
Mathivanan A, Senthilkumar A, Devakumaran K (2015) Pulsed current and dual pulse gas metal arc welding of grade AISI: 310S austenitic stainless steel. Def Technol 11(3):269–274. https://doi.org/10.1016/j.dt.2015.05.006
Simon F, Visakan K (2001) Approaches to intelligent control. In: Functional adaptive control: an intelligent systems approach. Springer, London, pp 5–6
Mvola B (2016) Adaptive gas metal arc welding control and optimization of welding parameters output: influence on welded joints. Int Rev Mech Eng 10(2):67–72
Pires J, Louriero A, Fereira P, Fernando B, Morgado J (2003) Welding robots. IEEE Robot Autom Mag 10(2):45–55
Zhu J, Song S, Shi H, Lee KY (2008) Investigation on control strategies for pulse gas metal arc welding process. In: Proceedings of IEEE Industrial Electronics and Applications (ICIEA), Singapore, Malaysia, pp. 1276–1281, 2008
Wu CS, Chen MA, LU YF (2005) Effect of current waveforms on metal transfer in pulsed gas metal arc welding. Meas Sci Technol 16(12):2459–2465
Joseph A, Farson D, Harwig D, Richardson R (2005) Influence of GMAW-P current waveforms on heat input and weld bead shape. Sci Technol Weld Join 10(3):311–318
Johnson JA, Carlson NM, Smartt HB, Clark DE (1991) Process control of GMAW: sensing of metal transfer mode. Weld J 70(4):91–99
Goyal VK, Ghosh PK, Saini JS (2008) Analytical studies on thermal behaviour and geometry of weld pool in pulsed current gas metal arc welding. J Mater Process Technol 209(3):1318–1336
Hermans MJM, Den Ouden G (1999) Process behavior and stability in short circuit gas metal arc welding. Weld J 78(4):137–141
Smith AA (1962) Characterisation of the short-circuiting CO2 shielded arc. Proceedings of International Symposium on Physics of the Welding Arc, The Welding Institute, London, UK, pp. 75–91
Voicu C, Mistodie LR, Rusu CC (2009) Correlations between drops dynamics and the GMAW-P arc stability. In: Proceedings of the International Conference New Technologies in Manufacturing (NEWTECH), Galati, pp. 23–25
Richardson IM, Bucknall PW, Stares I (1994) The influence of power source dynamics on wire melting rate in pulsed GMA welding. Weld J 73(2):32–37
Tong H, Ueyama (2001) Improvement of aluminium alloy sheet metal welding quality and productivity with AC pulsed MIG welding system (1st report). Development of AC pulsed MIG welding power source with built-in robot interface. Weld Int 15(11):851–856
Arif N, Chung H (2014) Alternating current-gas metal arc welding for applicationto thin sheets. J Mater Process Technol 214(9):828–1837
Saldanha d.N. A, Diandro Bailoni F, Mendes d.M. CA, Louriel Oliveira V (2009) Methodology for determination of parameters for welding MIG with variable polarity. Weld Int 23(6):473–480
Faria JP, Miranda HCDE, Motta MF, de Quieroz Paiva FD (2007) Effect of square-wave AC GMAW on weld beam geometry. Weld Int 21(3):212–219
Vilarinho LO, Nascimento AS, Fernandes DB, Mota CAM (2009) Methodology for parameter calculation of VP-GMAW. Weld J 88:92–98
Vilarinho LO, Nascimento AS (2012) Effect of waveform and shielding gas on melting rate and bead geometry for GMAW-VP and correlation to kinematics of metal transfer. In: Proceedings of the 9th International Conference, Trends in Welding Research, Chicago, Illinois, USA pp. 438–447
Mendes da Silva CL, Scotti A 2001, Assessment of the thermal pulsation periods on the weld bead formation in aluminum welding by the DP-GMAW technique, in 1st Brazilian Congress of Manufacturing Engineering – COBEF 2001, ABCM, Curitiba,
Chen MA, Wu CS, Li SK, Zhang YM (2007) Analysis of active control of metal transfer in modified pulsed GMAW. Sci Technol Weld Join 12(1):10–14
Zhang YM, Liguo E, Kovacevic R (1998) Active metal transfer control by monitoring excited droplet oscillation. Weld J 77(9):388–395
Zhang YM, Li PJ (2001) Modified active control of metal transfer and pulsed GMAW of titanium. Weld J 80(2):54–61
Sen M, Mukherjee M, Pal TK (2015) Evaluation of correlations between DP-GMAW process parameters and bead geometry. Weld J 94(8):265–279
Anhua L, Xinhua T, Fenggui L (2013) Weld pool profile characteristics of Al alloy in double-pulsed GMAW. Int J Adv Manuf Technol 68(9–12):2015–2023
da Silva CLM, Scotti A (2006) The influence of double pulse on porosity formation in aluminum GMAW. J Mater Process Technol 171(3):366–372
Zhang H, Hu S, Shen J, Ma L, Yin F (2015) Microstructures and mechanical properties of 30Cr-4Mo ferritic stainless steel joints produced by double-pulsed gas metal arc welding. Int J Adv Manuf Technol 80(9):1975–1983
Ushio M, Yamamoto H, Nishida Y, Mita T (1994) Recent advances in welding power systems for automated welding. Trans JWRI 23(1):1–6
Yamamoto H (1989) Recent advances in inverter controlled arc welding power sources and their application. J Jpn Weld Soc 58(4):272–279. https://doi.org/10.2207/qjjws1943.58.272
Lertora E, Gambaro C, Cypres P (2011) The influence of robotic MAG process welding parameters. Weld Int 25(10):767–776
Wu Y, Kovacevic R (2002) Mechanically assisted droplet transfer process in gas metal arc welding. Proc Inst Mech Eng 216(4):555–564
Pickin CG, Williams SW, Lunt M (2011) Characterisation of the cold metal transfer (CMT) process and its application for low dilution cladding. J Mater Process Technol 211(3):496–502
Kapustka N (2015) Achieving higher productivity rates using reciprocating wire feed gas metal arc welding. Weld J 94(4):70–74
Mezrag B, Deschaux-Beaume F, Benachour M (2015) Control of mass and heat transfer for steel/aluminium joining using cold metal transfer process. Sci Technol Weld Join 20(3):189–198
Torbati AM, Miranda RM, Quintino L, Williams S (2011) Welding bimetal pipes in duplex stainless steel. Int J Adv Manuf Technol 53(9–12):1039–1047
Mvola B, Kah P, Martikainen J, Hiltunen E (2013) Applications and benefits of adaptive pulsed GMAW. Mechanika 19(6):694–701
Praveen P, Kang M, Yarlagadda K (2006) Characterization of dynamic behaviour of short circuit in pulsed gas metal arc welding of aluminium. J Achiev Mater Manuf Eng 14(1–2):75–82
Trommer G (2009) Fronius: technologie—und anwendungsinnovationen-anwendungsinnovationen. Weld Cut Today 2:12–15
Picking CG, Young K (2006) Evaluation of cold metal transfer (CMT) process for welding aluminium alloy. Sci Technol Weld Join 11(5):583–585
Kolařík L, Kolaříková M, Kovanda K, Pantůček M, Vondrouš P (2012) Advanced functions of a modern power source for GMAW welding of steel. Acta Polytech 52(4):83–88
Cong B, Ding J, Williams S (2015) Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3% Cu alloy. Int J Adv Manuf Technol 76(9):1593–1606
Mvola B, Kah P (2016) Effects of shielding gas control: welded joint properties in GMAW process optimization. Int J Adv Manuf Technol 88(9–12):2369–2387. https://doi.org/10.1007/s00170-016-8936-2
T. M. V.-B. Rosado 2008 Innovation in the MIG/MAG process: productivity analysis and fume emissions. [Online]. Available: https://fenix.tecnico.ulisboa.pt. [Accessed 7 June 2016]
Goecke SF, Syed AA, Ebert-Spiegel M, De A (2013) Probing current, voltage and metal transfer characteristics in pulsed arc and conventional and novel low energy input short arc welding. J Jpn Weld Soc 31(4):26–30
Devakumaran K, Rajasekaran N, Ghosh PK (2012) Process characteristics of inverter type GMAW power source under static and dynamic operating conditions. Mater Manuf Process 27(12):1450–1456
Khorrami MS, Mostafaei M, Pouraliakbar H, Kokabi AH (2014) Study on microstructure and mechanical characteristics of low-carbon steel and ferritic stainless steel joints. Mater Sci Eng A 608:35–45
Pouraliakbar H, Hamedi M, Kokabi AH, Nazari A (2014) Designing of CK45 carbon steel and AISI 304 stainless steel dissimilar welds. Mater Res 17(1):106–114
Messer B, Patrick C, Seitza S (2006) Achieving cost savings with innovative welding and examination techniques. Int J Press Vessel Pip 83(5):365–372
Mathivanan A, Senthilkumar A, Devakumaran K (2015) Pulsed current and dual pulse gas metal arc welding of grade AISI: 310S austenitic stainless steel. Def Technol 11(3):269–274
Barcellona A, Bruccoleri M, D’Onofrio C, Palmeri D, Riccobono R 2007, Improving of the productivity and the quality of a manufacturing robotized cell for MIG/MAG welding, in Proceedings of the 35th International MATADOR Conference, Taiwan
Acknowledgements
This research was carried out in the Welding Technology Laboratory of LUT and funded by the Academy of Finland, Monitoring and Modeling of Advanced Adaptive Welding Process Systems for Ultra-High Strength Steel (UHSS) project under the project number SA 23B25105Y.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Mvola, B., Kah, P. & Layus, P. Review of current waveform control effects on weld geometry in gas metal arc welding process. Int J Adv Manuf Technol 96, 4243–4265 (2018). https://doi.org/10.1007/s00170-018-1879-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-1879-z