Skip to main content

Advertisement

Log in

Synthesis, microstructural and phase evolution in Ti–2Ni and Ti–10Ni binary alloys consolidated by spark plasma sintering technique

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The availability of lower-cost titanium with unique properties required for engineering applications such as in automobile, aerospace and biomedical has created a renewed interest in titanium and its alloys. However, poor sinterability due to high affinity of titanium for oxygen results in the production of less dense sintered product. While this may be of benefits in biomedical applications, it is deleterious to engineering applications such as in aviation parts that require high fatigue performance. In order to overcome this challenge, this study synthesized and consolidated Ti–2Ni and Ti–10Ni binary alloys using spark plasma sintering technique. Ti (Gd 1) and Ni elemental powders were mixed together in a TF2 Turbula mixer, at the speed of 101 rpm for 8 h. Sintering was conducted at 850, 1100 and 1200 °C under vacuum using the spark plasma sintering system. The applied pressure, heating rate and holding time were maintained at 50 MPa, 100 °C/min and 10 min respectively. Sample characterization was carried out with the aid of X-ray diffractometer and scanning electron microscope, equipped with energy-dispersive X-ray spectroscopy. The density and hardness of the sintered alloys were obtained using the Archimedes technique and Vickers microhardness tester respectively. The results showed that the relative density and hardness increased with increasing sintering temperature for the sintered Ti–2Ni and Ti–10Ni alloys. Generally, it was observed that increasing the sintering temperature and nickel addition improved the sinterability and densification of the sintered alloy.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

Similar content being viewed by others

References

  1. Mouritz AP (2012) 9—titanium alloys for aerospace structures and engines A2. In: Introduction to aerospace materials. Woodhead Publishing, Cambridge, pp 202–223

    Google Scholar 

  2. Noël JJ, Ebrahimi N, Shoesmith DW (2018) Corrosion of titanium and titanium alloys. In: Wandelt K (ed) Encyclopedia of interfacial chemistry. Elsevier, Oxford, pp 192–200

    Chapter  Google Scholar 

  3. Singh P, Pungotra H, Kalsi NS (2017) On the characteristics of titanium alloys for the aircraft applications. Mater Today: Proceedings 4:8971–8982, 2017/01/01/ 2017

    Google Scholar 

  4. Williams JC (2007) Titanium. Engineering materials and processes. Springer, Berlin

    Google Scholar 

  5. Niinomi M (2018) Titanium alloys. In: Reference module in biomedical sciences. Elsevier, Amsterdam

    Google Scholar 

  6. Froes FH (2016) Titanium: alloying. In: Reference module in materials science and materials engineering. Elsevier, Amsterdam

    Google Scholar 

  7. Lu J, Ge P, Zhao Y (2014) Recent development of effect mechanism of alloying elements in titanium alloy design. Rare Metal Mater Eng 43:775–779, 2014/04/01/ 2014

    Article  Google Scholar 

  8. Borkar T, Nag S, Ren Y, Tiley J, Banerjee R (2014) Reactive spark plasma sintering (SPS) of nitride reinforced titanium alloy composites. J Alloys Compd 617:933–945 /12/25/ 2014

    Article  Google Scholar 

  9. Panigrahi BB, Godkhindi MM, Das K, Mukunda PG, Ramakrishnan P (2005) Sintering kinetics of micrometric titanium powder. Mater Sci Eng A 396:255–262 /04/15/ 2005

    Article  Google Scholar 

  10. Shon J-h, Park J-m, Cho K-s, Hong J-k, Park N-k, Oh M-h (2014) Effects of various sintering methods on microstructure and mechanical properties of CP-Ti powder consolidations. Trans Nonferrous Metals Soc China 24:s59–s67, 2014/07/01/ 2014

    Article  Google Scholar 

  11. Flinn RA, Trojan PK (1990) Engineering materials and their applications, 4th edn. Houghton Mifflin Company, One Beacon Street, Boston MA 02108. USA

    Google Scholar 

  12. Shahedi Asl M, Sabahi Namini A, Motallebzadeh A, Azadbeh M (2018) Effects of sintering temperature on microstructure and mechanical properties of spark plasma sintered titanium. Mater Chem Phys 203:266–273, 2018/01/01/ 2018

    Article  Google Scholar 

  13. Polmear I, StJohn D, Nie J-F, Qian M (2017) 7.1 introduction. In: Light alloys—metallurgy of the light metals, 5th edn. Elsevier, Amsterdam pp. 369–370

  14. Froes FH (2015) 4.1 beta transformation. In: Titanium—physical metallurgy, processing, and applications. ASM International pp. 75–94

  15. Luo SD, Yang YF, Schaffer GB, Qian M (2013) The effect of a small addition of boron on the sintering densification, microstructure and mechanical properties of powder metallurgy Ti–7Ni alloy. J Alloys Compd 555:339–346, 2013/04/05/ 2013

    Article  Google Scholar 

  16. Robertson IM, Schaffer GB (2013) Suitability of nickel as alloying element in titanium sintered in solid state. Powder Metall 52:225–232, 2009/09/01 2009

    Article  Google Scholar 

  17. Liu H-W, Bishop DP, Plucknett KP (2015) A comparison of Ti–Ni and Ti-Sn binary alloys processed using powder metallurgy. Mater Sci Eng A 644:392–404 /09/17/ 2015

    Article  Google Scholar 

  18. Panigrahi BB (2007) Sintering behaviour of Ti–2Ni and Ti–5Ni elemental powders. Mater Lett 61:152–155, 2007/01/01/ 2007

    Article  Google Scholar 

  19. Carman A, Zhang LC, Ivasishin OM, Savvakin DG, Matviychuk MV, Pereloma EV (2011) Role of alloying elements in microstructure evolution and alloying elements behaviour during sintering of a near-β titanium alloy. Mater Sci Eng A 528:1686–1693, 2011/01/25/ 2011

    Article  Google Scholar 

  20. Makena MI, Shongwe MB, Ramakokovhu MM, Olubambi PA (2017) Effect of sintering parameters on densification, corrosion and wear behaviour of Ni-50Fe alloy prepared by spark plasma sintering. J Alloys Compd 699:1166–1179, 2017/03/30/

    Article  Google Scholar 

  21. Guillon O, Gonzalez-Julian J, Dargatz B, Kessel T, Schierning G, Räthel J et al (2014) Field-assisted sintering technology/spark plasma sintering: mechanisms, materials, and technology developments. Adv Eng Mater 16:830–849, 2014/07/01 2014

    Article  Google Scholar 

  22. Feng H, Zhou Y, Jia D, Meng Q (2005) Rapid synthesis of Ti alloy with B addition by spark plasma sintering. Mater Sci Eng A 390:344–349 /01/15/ 2005

    Article  Google Scholar 

  23. Zhang Z-h, Shen X-B, Wen S, Luo J, Lee S-k, Wang F-c (2010) In situ reaction synthesis of Ti–TiB composites containing high volume fraction of TiB by spark plasma sintering process. J Alloys Compd 503:145–150, 2010/07/30/ 2010

    Article  Google Scholar 

  24. Kundu S, Hussain M, Kumar V, Kumar S, Das AK (2018) Direct metal laser sintering of TiN reinforced Ti6Al4V alloy based metal matrix composite: fabrication and characterization. Int J Adv Manuf Technol 97:2635–2646 /07/01 2018

    Article  Google Scholar 

  25. Zhang P, Zhang DZ, Peng D, Li Z, Mao Z (2018) Rolling contact fatigue performance evaluation of Ti–6Al–4V parts processed by selective laser melting. Int J Adv Manuf Technol 96:3533–3543, 2018/06/01 2018

    Article  Google Scholar 

  26. Fotovvati B, Namdari N, Dehghanghadikolaei A (2018) Fatigue performance of selective laser melted Ti6Al4V components: state of the art. Materials research express 6:012002, 2018/10/05

    Article  Google Scholar 

  27. Robertson IM, Schaffer GB (2013) Swelling during liquid phase sintering of Ti–Ni alloys. Powder Metall 52:213–224, 2009/09/01 2009

    Article  Google Scholar 

  28. ASTM E3-11 (2017) Standard guide for preparation of metallographic specimen 2017 ed. vol. 03. ASTM International, West Conshohocken, PA

    Google Scholar 

  29. Shongwe MB, Diouf S, Durowoju MO, Olubambi PA (2015) Effect of sintering temperature on the microstructure and mechanical properties of Fe–30%Ni alloys produced by spark plasma sintering. J Alloys Compd 649:824–832 /11/15/ 2015

    Article  Google Scholar 

  30. Babalola BJ, Shongwe MB, Obadele BA, Olubambi PA (2018) Densification, microstructure and mechanical properties of spark plasma sintered Ni-17%Cr binary alloys. Int J Adv Manuf Technol 101:1573–1581, 2018/11/22

  31. Tokita M (2011) The potential of spark plasma sintering (SPS) method for the fabrication on an industrial scale of functionally graded materials. Adv Sci Technol 63:322–331

    Article  Google Scholar 

  32. Diouf S, Molinari A (2012) Densification mechanisms in spark plasma sintering: effect of particle size and pressure. Powder Technol 221:220–227, 2012/05/01/ 2012

    Article  Google Scholar 

  33. Oke SR, Ige OO, Falodun OE, Obadele BA, Shongwe MB, Olubambi PA (2018) Optimization of process parameters for spark plasma sintering of nano structured SAF 2205 composite. J Mater Res Technol 7:126–134, 2018/04/01/ 2018

    Article  Google Scholar 

Download references

Funding

This work is based on the research supported by the National Research Foundation (NRF) of South Africa for the Unique Grant No. 117867.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Azeez Lawan Rominiyi.

Additional information

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Rominiyi, A.L., Shongwe, M.B., Maledi, N. et al. Synthesis, microstructural and phase evolution in Ti–2Ni and Ti–10Ni binary alloys consolidated by spark plasma sintering technique. Int J Adv Manuf Technol 104, 1041–1049 (2019). https://doi.org/10.1007/s00170-019-03950-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-019-03950-5

Keywords

Navigation