Abstract
Additive manufacturing (AM) possesses appealing potential for manipulating material compositions, structures and properties in end-use products with arbitrary shapes without the need for specialized tooling. Since the physical process is difficult to experimentally measure, numerical modeling is a powerful tool to understand the underlying physical mechanisms. This paper presents our latest work in this regard based on comprehensive material modeling of process–structure–property relationships for AM materials. The numerous influencing factors that emerge from the AM process motivate the need for novel rapid design and optimization approaches. For this, we propose data-mining as an effective solution. Such methods—used in the process–structure, structure–properties and the design phase that connects them—would allow for a design loop for AM processing and materials. We hope this article will provide a road map to enable AM fundamental understanding for the monitoring and advanced diagnostics of AM processing.
Similar content being viewed by others
References
ASTM (2014) Standard terminology for additive manufacturing technologies. ASTM International, West Conshohocken (2014)
Yang L, Harrysson O, West H, Cormier D (2012) Compressive properties of Ti–6Al–4V auxetic mesh structures made by electron beam melting. Acta Mater 60(8):3370–3379
Ge W, Lin F, Guo C (2015) Microstructure and mechanical property of electron beam selective melting Ti–6Al–4V/Ti–Al structural gradient material. In: 26th Annual international symposium on solid freeform fabrication, Austin, Texas
Ge W, Guo C, Lin F (2015) Microstructures of components synthesized via electron beam selective melting using blended pre-alloyed powders of Ti–6Al–4V and Ti–45Al–7Nb. Rare Metal Mater Eng 44:2623–2627
Guo C, Ge W, Lin F (2015) Dual-material electron beam selective melting: hardware development and validation studies. Engineering 1(1):124
Ma C, Gu D, Dai D, Chen W, Chang F, Yuan P, Shen Y (2015) Aluminum-based nanocomposites with hybrid reinforcements prepared by mechanical alloying and selective laser melting consolidation. J Mater Res 30(18):2816–2828
Tan X, Kok Y, Tan YJ, Descoins M, Mangelinck D, Tor SB, Leong KF, Chua CK (2015) Graded microstructure and mechanical properties of additive manufactured Ti–6Al–4V via electron beam melting. Acta Mater 97:1–16
Ramsperger M, Körner C (2016) SEBM of the single crystalline Ni-based superalloy CMSX-4. In: the 1st EBAM conference, Nuremberg, Germany
Dehoff R, Kirka M, Sames W, Bilheux H, Tremsin A, Lowe L, Babu S (2015) Site specific control of crystallographic grain orientation through electron beam additive manufacturing. Mater SciTechnol 31(8):931–938
Morton PA, Mireles J, Mendoza H, Cordero PM, Benedict M, Wicker RB (2015) Enhancement of low-cycle fatigue performance from tailored microstructures enabled by electron beam melting additive manufacturing technology. J Mech Des 137(11):111412
Yadroitsau I (2009) Selective laser melting: direct manufacturing of 3D-objects by selective laser melting of metal powders. Lambert Academic Publishing, Saarbrucken
Yan W, Ge W, Smith J, Wagner G, Lin F, Liu WK (2015) Towards high-quality selective beam melting technologies: modeling and experiments of single track formations. In: 26th Annual international symposium on solid freeform fabrication, Austin, Texas
Kundakcioglu E, Lazoglu I, Rawal S (2016) Transient thermal modeling of laser-based additive manufacturing for 3D freeform structures. Int J Adv Manuf Technol 85(1–4):493–501
Roberts I, Wang C, Esterlein R, Stanford M, Mynors D (2009) A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing. Int J Mach Tools Manuf 49(12):916–923
Parry L, Ashcroft I, Wildman R (2016) Understanding the effect of laser scan strategy on residual stress in selective laser melting through thermo-mechanical simulation. Addit Manuf 12:1–15
Heigel J, Michaleris P, Reutzel E (2015) Thermo-mechanical model development and validation of directed energy deposition additive manufacturing of Ti–6Al–4V. Addit Manuf 5:9–19
Hodge N, Ferencz R, Solberg J (2014) Implementation of a thermomechanical model for the simulation of selective laser melting. Comput Mech 54(1):33–51
Smith J, Xiong W, Cao J, Liu WK (2016) Thermodynamically consistent microstructure prediction of additively manufactured materials. Comput Mech 57:359–370
Ghosh S (2006) Process modeling for solidification microstructure and transient thermal stresses in laser aided DMD process. Ph.D. thesis, University of Missouri, Rolla
Schoinochoritis B, Chantzis D, Salonitis K (2017) Simulation of metallic powder bed additive manufacturing processes with the finite element method: a critical review. Proc Inst Mech Eng Part B J Eng Manuf 231:96–117
Körner C, Bauereiß A, Attar E (2013) Fundamental consolidation mechanisms during selective beam melting of powders. Modelling Simul Mater Sci Eng 21(8):085011
Khairallah SA, Anderson AT, Rubenchik A, King WE (2016) Laser powder-bed fusion additive manufacturing: physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones. Acta Mater 108:36–45
Qiu C, Panwisawas C, Ward M, Basoalto HC, Brooks JW, Attallah MM (2015) On the role of melt flow into the surface structure and porosity development during selective laser melting. Acta Mater 96:72–79
Rai A, Markl M, Körner C (2016) A coupled cellular automaton–lattice Boltzmann model for grain structure simulation during additive manufacturing. Comput Mater Sci 124:37–48
Panwisawas C, Qiu C, Anderson MJ, Sovani Y, Turner RP, Attallah MM, Brooks JW, Basoalto HC (2017) Mesoscale modelling of selective laser melting: thermal fluid dynamics and microstructural evolution. Comput Mater Sci 126:479–490
Francois M, Sun A, King W, Henson N, Tourret D, Bronkhorst C, Carlson N, Newman C, Haut T, Bakosi J et al (2017) Modeling of additive manufacturing processes for metals: Challenges and opportunities. Curr Opin Solid State Mater Sci 21:24513
Smith J, Xiong W, Yan W, Lin S, Cheng P, Kafka OL, Wagner GJ, Cao J, Liu WK (2016) Linking process, structure, property, and performance for metal-based additive manufacturing: computational approaches with experimental support. Comput Mech 57:583–610
Leuders S, Vollmer M, Brenne F, Tröster T, Niendorf T (2015) Fatigue strength prediction for titanium alloy tial6v4 manufactured by selective laser melting. Metall Mater Trans A 46(9):3816–3823
Hedayati R, Hosseini-Toudeshky H, Sadighi M, Mohammadi-Aghdam M, Zadpoor A (2016) Computational prediction of the fatigue behavior of additively manufactured porous metallic biomaterials. Int J Fatigue 84:67–79
Yan W, Ge W, Smith J, Lin S, Kafka OL, Lin F, Liu WK (2016) Multi-scale modeling of electron beam melting of functionally graded materials. Acta Mater 115:403–412
Yan W, Smith J, Ge W, Lin F, Liu WK (2015) Multiscale modeling of electron beam and substrate interaction: a new heat source model. Comput Mech 56(2):265–276
Carriere P, Yue S (2017) Energy absorption during pulsed electron beam spot melting of 304 stainless steel: Monte-carlo simulations and in-situ temperature measurements. Vacuum 142:114–122
Yan W, Qian Y, Ge W, Lin S, Liu WK, Lin F, Wagner GJ (2018) Meso-scale modeling of multiple-layer fabrication process in selective electron beam melting: inter-layer/track voids formation. Mater Des 141:210–219
Yan W, Ge W, Qian Y, Lin S, Zhou B, Liu WK, Lin F, Wagner GJ (2017) Multi-physics modeling of single/multiple-track defect mechanisms in electron beam selective melting. Acta Mater 134:324–333
Yan W, Lin S, Kafka OL, Yu C, Liu Z, Lian Y, Wolff S, Cao J, Wagner GJ, Liu WK Modeling process–structure–property relationships for additive manufacturing. Front Mech Eng (Accepted)
Johnson K, Kendall K, Roberts A (1971) Surface energy and the contact of elastic solids. In: Proceedings of the royal society of London A: mathematical, physical and engineering sciences, vol 324. The Royal Society, pp. 301–313
Hirt CW, Nichols BD (1981) Volume of fluid (vof) method for the dynamics of free boundaries. J Comput Phys 39(1):201–225
Lian Y, Lin S, Yan W, Liu WK, Wagner GJ A parallelized three-dimensional cellular automaton model for grain growth during additive manufacturing. Comput Mech (Accepted)
Kurz W, Giovanola B, Trivedi R (1986) Theory of microstructural development during rapid solidification. Acta Metall 34(5):823–830
Lipton J, Glicksman M, Kurz W (1984) Dendritic growth into undercooled alloy melts. Mater Sci Eng 65:57–63
Gandin C-A, Rappaz M (1994) A coupled finite element-cellular automaton model for the prediction of dendritic grain structures in solidification processes. Acta Metall Mater 42(7):2233–2246
Dezfoli ARA, Hwang W-S, Huang W-C, Tsai T-W (2017) Determination and controlling of grain structure of metals after laser incidence: theoretical approach. Sci Rep 7:41527
Hashemi H, Sliepcevich C (1967) A numerical method for solving two-dimensional problems of heat conduction with change of phase. Chem Eng Progr Symp Ser 63:34–41
Wolff SJ, Lin S, Faierson EJ, Liu WK, Wagner GJ, Cao J (2017) A framework to link localized cooling and properties of directed energy deposition (DED)-processed Ti–6Al–4V. Acta Mater 132:106–117
Liu Z, Moore JA, Aldousari SM, Hedia HS, Asiri SA, Liu WK (2015) A statistical descriptor based volume-integral micromechanics model of heterogeneous material with arbitrary inclusion shape. Comput Mech 55(5):963–981
Liu Z, Bessa M, Liu WK (2016) Self-consistent clustering analysis: an efficient multi-scale scheme for inelastic heterogeneous materials. ComputMethods ApplMech Eng 306:319–341
Liu Z, Moore JA, Liu WK (2016) An extended micromechanics method for probing interphase properties in polymer nanocomposites. J Mech Phys Solids 95:663–680
Goury O, Amsallem D, Bordas SPA, Liu WK, Kerfriden P (2016) Automatised selection of load paths to construct reduced-order models in computational damage micromechanics: from dissipation-driven random selection to bayesian optimization. Comput Mech 58(2):213–234
Liu Z, Kafka OL, Yu C, Liu WK (2018) Data-driven self-consistent clustering analysis of heterogeneous materials with crystal plasticity. In: Onate E, Peric D, de Souze Neto E, Chiumenti M (eds) Advances in computational plasticity. Springer, pp. 221–242
Groeber MA, Jackson MA (2014) Dream. 3D: A digital representation environment for the analysis of microstructure in 3D. Integr Mater Manuf Innov 3(1):5
Moore JA, Frankel D, Prasannavenkatesan R, Domel AG, Olson GB, Liu WK (2016) A crystal plasticity-based study of the relationship between microstructure and ultra-high-cycle fatigue life in nickel titanium alloys. Int J Fatigue 91(1):183–194
Moulinec H, Suquet P (1998) A numerical method for computing the overall response of nonlinear composites with complex microstructure. Comput Methods Appl Mech Eng 157(1–2):69–94
Moore JA, Ma R, Domel AG, Liu WK (2014) An efficient multiscale model of damping properties for filled elastomers with complex microstructures. Compos Part B Eng 62:262–270
Bessa M, Bostanabad R, Liu Z, Hu A, Apley DW, Brinson C, Chen W, Liu WK (2017) A framework for data-driven analysis of materials under uncertainty: countering the curse of dimensionality. Comput Methods Appl Mech Eng 320:633–667
Witten IH, Frank E (2005) Data mining: practical machine learning tools and techniques. Morgan Kaufmann, Burlington
Mani M, Lane BM, Donmez MA, Feng SC, Moylan SP (2017) A review on measurement science needs for real-time control of additive manufacturing metal powder bed fusion processes. Int J Prod Res 55(5):1400–1418
Zhao C, Fezzaa K, Cunningham RW, Wen H, De Carlo F, Chen L, Rollett AD, Sun T (2017) Real-time monitoring of laser powder bed fusion process using high-speed X-ray imaging and diffraction. Sci Rep 7:3602
Yan W, Lian Y, Yu C, Kafka OL, Liu Z, Liu WK, Wagner GJ An integrated process-structure-property modeling framework for additive manufacturing. (Under review)
Liu WK, Jun S, Zhang Y (1995) Reproducing kernel particle methods. Int J Numer Methods Fluids 20:1081–1106
Ted B, Lu Y, Gu L (1994) Element-Free Galerkin methods. Int J Numer Methods Eng 37(2):229–256
Lian Y, Zhang X, Liu Y (2012) An adaptive finite element material point method and its application in extreme deformation problems. Comput Methods Appl Mech Eng 241:275–285
Vernerey F, Liu W, Moran B (2007) Multi-scale miromorphic theory for hierarchical materials. J Mech Phys Solids 55(12):2603–2651
Tang S, Kopacz AM, Chan O’Keeffe S, Olson GB, Liu WK (2013) Concurrent multiresolution finite element: formulation and algorithmic aspects. Comput Mech 52(6):1265–1279
Acknowledgements
W. K. Liu, W. Yan and J. Cao acknowledge the support by National Institute of Standards and Technology (NIST) Center for Hierarchical Materials Design (CHiMaD) under grant No. 70NANB14H012. K. Ehmann, G. J. Wagner J. Cao and W. K. Liu acknowledge the support by the National Science Foundation (NSF) Cyber-Physical Systems (CPS) under grant No. CPS/CMMI-1646592. The support from DMDII (Digital Manufacturing Design Innovation Institute) is also acknowledged. S. Lin and O.L. Kafka acknowledge the support of the National Science Foundation Graduate Research Fellowship under Grant No. DGE-1324585. The tomographic image of Figs. 16 and 17 used resources of the Advanced Photon Source (APS), a U.S. Department of Energy (DOE) Office of Science User Facility operated for the DOE Office of Science by Argonne National Laboratory under Contract No. DE-AC02-06CH11357. We thank Dr. Xianghui Xiao and Dr. Tao Sun for the assistance at APS beamlines.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yan, W., Lin, S., Kafka, O.L. et al. Data-driven multi-scale multi-physics models to derive process–structure–property relationships for additive manufacturing. Comput Mech 61, 521–541 (2018). https://doi.org/10.1007/s00466-018-1539-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00466-018-1539-z