Abstract
Significant improvement in load capacity, wear resistance, friction coefficient etc. of tribological mechanical components can be obtained by forming regular micro-surface structure in the form of micro-dimples on their surfaces. A feasibility study was performed both theoretically and experimentally using the Laser Surface Texturing (LST) technique to produce the micro-dimples. Each micro-dimple can serve either as a micro-hydrodynamic bearing in cases of full or mixed lubrication or as a micro-reservoir for lubricant in cases of starved lubrication conditions. Theoretical models were developed, and laboratory tests were performed, to investigate the potential of LST in tribological components like mechanical seals, piston rings and thrust bearings. In the entire laboratory tests, friction was substantially reduced with LST compared to the non-textured components.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Y. R. Jeng, Tribol. Trans. 39 (1996), 2, 354.
E. Willis, Wear 109 (1986) 351.
R. Ranjan, D. N. Lambeth, M. Tromel, P. Goglia and Y. Li, J. Appl. Phys. 69 (1991), 8, 5745.
L. Zhou, K. Kato, G. Vurens and F. E. Talke, Tribol. Int. 36 (2003) 269.
K. Komvopoulos, J. Adhes. Sci. Technol. 17 (2003) 477.
M. Wakuda, Y. Yamauchi, S. Kanzaki and Y. Yasuda, Wear 254 (2003) 356.
X. L. Wang and K. Kato, Tribol. Lett. 14 (2003) 275.
X. L. Wang, K. Kato, K. Adachi and K. Aizawa, Tribol. Int. 36 (2003) 189.
G. Dumitru, V. Romano, H. P. Weber, H. Haefke, Y. Gerbig and E. Pflu¨ ger, Appl. Phys. A 70 (2000) 485.
T. V. Kononenko, S. V. Garnov, S. M. Pimenov, V. I. Onov, V. Romano, B. Borsos and H. P. Weber, Appl. Phys. A 71 (2000) 627.
A. A. Voevodin, J. Bultman and J. S. Zabinski, Surf. Coat. Technol. 107 (1998) 12.
U. Pettersson and S. Jacobson, Tribol. Int. 36 (2003) 857.
M. Geiger, S. Roth and W. Becker, Surf. Coat. Technol. 100–101 (1998) 17.
D. B. Hamilton, J. A. Walowit and C. M. Allen, ASME J. Basic Eng. 88 (1966) 177.
J. N. Anno, J. A. Walowit and C. M. Allen, ASME J. Lubricat. Technol. 90 (1968) 351.
J. N. Anno, J. A. Walowit and C. M. Allen, ASME J. Lubricat. Technol. 91 (1969) 726.
I. Etsion and L. Burstein, Tribol. Trans. 39 (1996) 677.
I. Etsion, G. Halperin and Y. Greenberg, in: Proc. 15th Int. Conf. On Fluid Sealing BHR Group (Maastricht, 1997) pp. 3.
I. Etsion, Y. Kligerman and G. Halperin, Tribol. Trans. 42 (1999) 511.
I. Etsion, in: Proc. 17th Int. Pump Users Symposium (2000) pp. 17.
I. Etsion and G. Halperin, Tribol. Trans. 45 (2002) 430.
S. Pride, K. Folkert, P. Guichelaar and I. Etsion, Lubricat. Engg. 58 (2002) 16.
Y. Kligerman and I. Etsion, Tribol. Trans. 44 (2001) 472.
A. Hoppermann and M. Kordt, O+P “Oelhydraulik und Pneumatik”, Vereinigte Fachverlage Mainz, ISSN 0341-2660, (2002).
A. Ronen, I. Etsion and Y. Kligerman, Tribol. Trans. 44 (2001) 359.
G. Ryk, Y. Kligerman and I. Etsion, Tribol. Trans. 45 (2002) 444.
V. Brizmer, Y. Kligerman and I. Etsion, Tribol. Trans. 46 (2003) 397.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Etsion, I. Improving Tribological Performance of Mechanical Components by Laser Surface Texturing. Tribology Letters 17, 733–737 (2004). https://doi.org/10.1007/s11249-004-8081-1
Issue Date:
DOI: https://doi.org/10.1007/s11249-004-8081-1