Abstract
Advances toward low friction surfaces are in growing demand from many economic sectors for energy efficiency and environmental safety. However, the traditional approach of multi-grade oil formulation is limited by its inability to induce pollution-free generation of uniform oil-retaining films needed to improve surface lubricity. Here, a direct route to the formation of a surface layer of superior lubricity is presented as an alternative to the use of oil additives for friction reduction. The deformation-induced generation of a surface film consisting of low-shear-strength oil-retaining compounds is obtained via supplying chemically beneficial elements during a widely used surface finishing mechanical treatment. An ultra-low friction coefficient of about 0.01 is obtained with base oil lubrication after tailoring the surface chemistry by shot peening using a mixture of Cu2S and Al2O3; this result opens new horizons for surface engineering.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Moore, D.F.: Principles and Applications of Tribology, 1st edn. Pergamon Press, Oxford (1975)
Bhushan, B.: Introduction to Tribology. Wiley, New York (2002)
Holmberg, K., Andersson, P., Erdemir, A.: Global energy consumption due to friction in passenger cars. Tribol. Int. 47, 221–234 (2012)
Dowson, D.: History of Tribology. Longman, London (1979)
Rabinowicz, E.: Friction and Wear of Materials. Wiley, New York (1965)
Czichos, H.: Tribology: A Systems Approach to the Science and Technology of Friction, Lubrication, and Wear. Elsevier, New York (1978)
Bowden, F.P., Gregory, J.N., Tabor, D.: Lubrication of metal surfaces by fatty acids. Nature 156, 97–101 (1945)
Ludema, K.C.: Friction, Wear, Lubrication: A Textbook in Tribology. CRC Press, Boca Raton (1996)
Hutchings, I.M.: Tribology: Friction and Wear of Engineering Materials. Edward Arnold, London (1992)
Blau, P.J.: Friction Science and Technology: From Concepts to Applications, 2nd edn. CRC Press, Boca Raton (2008)
Shitara, Y., Suzuki, S., Kaimai, T., Nanao, H., Mori, S.: Improvement of tribological properties with gallic acid derivatives in boundary lubrication. J Jpn Soc Tribol 56(1), 55–61 (2011)
Kalpakjian, S., Schmid, S.R.: Manufacturing Processes for Engineering Materials, 5th edn. Pearson Education, Upper Saddle River (2008)
Kostetskii, B.I., Nosovskii, I.G., Karaulov, A.K., Bershadskii, L.I., Kostetskaya, N.B., Lyashko, V.A., Sagach, M.F.: The Surface Strength of Materials in Friction (In Russian). Tekhnika, Kiev (1976)
Fischer, T.E.: Tribochemistry. Annu. Rev. Mater. Sci. 18, 303–323 (1988)
Felts, J.R., Oyer, A.J., Hernandez, S.C., Whitener, K.E., Robinson, J.T., Walton, S.G., Sheehan, P.E.: Direct mechanochemical cleavage of functional groups from graphene. Nat. Commun. 6, 6467 (2015)
Gosvami, N.N., Bares, J.A., Mangolini, F., Konicek, A.R., Yablon, D.G., Carpick, R.W.: Mechanisms of antiwear tribofilm growth revealed in situ by single-asperity sliding contacts. Science 348, 102–106 (2015)
Sundararajan, G., Roy, M.: Solid particle erosion behaviour of metallic materials at room and elevated temperatures. Tribol. Int. 30, 339–359 (1997)
Torosyan, A., Takacs, L.: Mechanochemical reaction at the interface between a metal plate and oxide powders. J. Mater. Sci. 39, 5491–5496 (2004)
Varenberg, M.: Towards a unified classification of wear. Friction 1, 333–340 (2013)
Vanysek, P.: Electrochemical series. http://issuu.com/time-to-wake-up/docs/electrochemical_redox_potential. Accessed June 16 2015
Calka, A., Wexler, D., Monaghan, B., Mosbah, A., Balaz, P.: Rapid reduction of copper sulfide (Cu2S) with elemental Fe and Mg using electrical discharge assisted mechanical milling (EDAMM). J. Alloy. Compd. 486, 492–496 (2009)
Dehm, G., Medres, B., Shepeleva, L., Scheu, C., Bamberger, M., Mordike, B.L., Mordike, S., Ryk, G., Halperin, G., Etsion, I.: Microstructure and tribological properties of Ni-based claddings on Cu substrates. Wear 225, 18–26 (1999)
Hirst, W., Hollander, A.E.: Surface finish and damage in sliding. Proc. R. Soc. Lon. Ser. A 337, 379–394 (1974)
Greenwood, J.A., Williamson, J.B.P.: Contact of nominally flat surfaces. Proc. R. Soc. Lon. Ser. A 295, 300–319 (1966)
Wang, Y.H., Wan, Y., Wang, W.X., Yang, S.Y.: Friction-reducing properties of stearic acid modification of the Cu2S film on the copper substrate. J. Alloy. Compd. 557, 179–183 (2013)
Rapoport, L., Fleischer, N., Tenne, R.: Fullerene-like WS2 nanoparticles: superior lubricants for harsh conditions. Adv. Mater. 15, 651–655 (2003)
Greenberg, R., Halperin, G., Etsion, I., Tenne, R.: The effect of WS2 nanoparticles on friction reduction in various lubrication regimes. Tribol. Lett. 17, 179–186 (2004)
Acknowledgments
We acknowledge the support of the Grand Technion Energy Program, the Carl E. Schustak Energy Research and Development Fund, and the New York Metropolitan Research Fund to M.V. This work was performed in part at the Georgia Tech Institute for Electronics and Nanotechnology, a member of the National Nanotechnology Coordinated Infrastructure, which is supported by the National Science Foundation (Grant ECCS-1542174).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Varenberg, M., Ryk, G., Yakhnis, A. et al. Mechano-Chemical Surface Modification with Cu2S: Inducing Superior Lubricity. Tribol Lett 64, 28 (2016). https://doi.org/10.1007/s11249-016-0758-8
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11249-016-0758-8