Skip to main content
SpringerLink
Log in

Acicular ferrite morphologies in a medium-carbon microalloyed steel

  • Published:
Metallurgical and Materials Transactions A Aims and scope Submit manuscript

Abstract

The influence of time and isothermal transformation temperature on the morphology of acicular ferrite in a medium-carbon microalloyed steel has been studied using optical and transmission electron microscopy (TEM). This study has been carried out with the analysis of the microstructures obtained with one- and two-stage isothermal treatments at 400 °C and 450 °C, following austenitization at 1250 °C. The heat treatments were interrupted at different times to observe the evolution of the microstructure at each temperature. The results show that a decrease in the isothermal transformation temperature gives rise to the development of sheaves of parallel ferrite plates, similar to bainitic sheaves, but intragranularly nucleated. These replace the face-to-edge nucleation that dominates the transformation at higher temperatures. The TEM observations reveal that the plates correspond to upper acicular ferrite and the sheaves to lower acicular ferrite. In this last case, cementite precipitates are present at the ferrite unit interiors and between the different platelets.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. H.K.D.H. Bhadeshia: Bainite in Steels. Transformations, Microstructure and Properties, 2nd Edition, The Institute of Materials, London, 2001, ch. 10.

    Google Scholar 

  2. Z. Zhang and R.A. Farrar: Mater. Sci. Technol., 1996, vol. 12, pp. 237–60.

    CAS  Google Scholar 

  3. S.S. Babu and H.K.D.K. Bhadeshia: Mater. Sci. Eng. A, 1992, vol. 156, pp. 1–9.

    Article  Google Scholar 

  4. M. Strangwood and H.K.D.H. Bhadeshia: Proc. Int. Conf. Advances in Welding Science and Technology, ASM, Cleveland, OH, 1987, pp. 187–91.

    Google Scholar 

  5. D.J. Abson and R.E. Dolby: Weld. Inst. Res. Bull., 1987, vol. 19, pp. 202–07.

    Google Scholar 

  6. R.C. Cochrane and P.R. Kirkwood: in Trends in Steels and Consumables for Welding, The Welding Institute, Abingdon, 1978, pp. 103–21.

    Google Scholar 

  7. O. Grong and D.K. Matlock: Int. Met. Rev., 1986, vol. 31 (1), pp. 27–48.

    CAS  Google Scholar 

  8. R.A. Ricks, P.R. Howell, and G.S. Barritte, Jr.: Mater. Sci., 1982, vol. 17, pp. 732–40.

    Article  CAS  Google Scholar 

  9. S. Ohkita, H. Homma, S. Tsushima, and N. Mori: Aus. Welding J., 1984, pp. 29–36.

  10. D.J. Abson, R.E. Dolby, and P.H.M. Hart: Trends in Steels and Consumables for Welding, Conf. Proc., The Welding Institute, Abingdon, 1987, pp. 75–101.

    Google Scholar 

  11. J.G. Garland and P.R. Kirkwood: Met. Constr., 1975, vol. 7 (5), pp. 275–83.

    CAS  Google Scholar 

  12. J.G. Garland and P.R. Kirkwood: Met. Constr., 1975, vol. 7 (6), pp. 320–30.

    CAS  Google Scholar 

  13. J.M. Dowling, J.M. Corbett, and H.W. Kerr: Metall. Trans. A, 1986, vol. 17, pp. 1611–23.

    Google Scholar 

  14. O. Grong and D.K. Matlock: Int. Met. Rev., 1986, vol. 31 (1), pp. 27–44.

    CAS  Google Scholar 

  15. E.S. Kayali, J.M. Corbett, and H.W. Kerr: J. Mater. Sci. Lett., 1983, vol. 2, pp. 123–28.

    Article  CAS  Google Scholar 

  16. S.K. Liu and D.L. Olson: Weld. Res. Suppl., 1986, vol. 65, pp. 139s-149s.

    Google Scholar 

  17. M. Imagumbai, R. Chijiiwa, N. Aikawa, M. Nagumo, H. Homma, M. Matsuda, and H. Mimura: HSLA Steels: Metallurgy and Aplications, J.M. Gray, T. Ko, Z. Shouhua, W. Baorong, and X. Xishan, eds., ASM INTERNATIONAL, Metals Park, OH, 1985, pp. 557–66.

    Google Scholar 

  18. T. Ochi, T. Takahashi, and H. Takada: Proc. 30th Mechanical Working and Steel Processing Conf., Iron and Steel Society, Warrendale, PA, 1989, vol. XXVI, pp. 65–72.

    Google Scholar 

  19. F.J. Barbaro, P. Krauklis, and K.E. Easterling: Mater. Sci. Technol., 1989, vol. 5, pp. 1057–68.

    CAS  Google Scholar 

  20. F. Ishikawa, T. Takahashi, and T. Ochi: Metall. Mater. Trans. A, 1994, vol. 25A, pp. 929–36.

    CAS  Google Scholar 

  21. J.M. Gregg and H.K.D.H. Bhadeshia: Acta Mater., 1997, vol. 45 (2), pp. 739–48.

    Article  CAS  Google Scholar 

  22. K. Yamamoto, T. Hasegawa, and J. Takamura: Iron Steel Inst. Jpn. Int., 1996, vol. 36, pp. 80–86.

    CAS  Google Scholar 

  23. E. Anelli, C. Andena, S. Matera, P. Harrison, I. Gutierrez, D. Porter, and T. Siwecki: ECSC Research Project Agreement 7210 PR/037 (97-D3.05a,b,c,d,e), 1998 Annual Report.

  24. M.A. Linaza, J.L. Romero, J.M. Rodriguez-Ibabe, and J.J. Urcola: Scripta Metall. Mater., 1993, vol. 29, pp. 1217–22.

    Article  CAS  Google Scholar 

  25. M.A. Linaza, J.L. Romero, J.M. Rodriguez-Ibabe, and J.J. Urcola: Scripta Metall. Mater., 1995, vol. 32, pp. 395–400.

    Article  CAS  Google Scholar 

  26. I. Madariaga and I. Gutierrez: Scripta Mater., 1997, vol. 37 (8), pp. 1185–92.

    Article  CAS  Google Scholar 

  27. I. Madariaga, J.L. Romero, and I. Gutiérrez: Metall. Mater. Trans. A, 1998, vol. 29A, pp. 1003–15.

    CAS  Google Scholar 

  28. I. Madariaga and I. Gutiérrez: Acta Mater., 1999, vol. 47 (3), pp. 951–60.

    Article  CAS  Google Scholar 

  29. M. Díaz-Fuentes, I. Madariaga, J.M. Rodríguez-Ibabe, and I. Gutiérrez: J. Construct. Steel Res., 1998, vol. 46 (1–3), pp. 413–14.

    Article  Google Scholar 

  30. M. Díaz-Fuentes, I. Madariaga, and I. Gutiérrez: in Microalloying in Steels, J.M. Rodriguez-Ibabe, I. Gutierrez, and B. Lopez, eds., Materials Science Forum Vols. 284–286, Trans Tech Publications Ltd., Aedermannsdorf, Switzerland, 1998, pp. 245–52.

    Google Scholar 

  31. J.L. Romero, M.A. Linaza, J.I. San Martin, J.M. Rodriguez-Ibabe, and J.J. Urcola: Rev. Met. CENIM, 1996, vol. 32, pp. 1–13.

    Google Scholar 

  32. I. Madariaga and I. Gutiérrez: in Microalloying in Steels, J.M. Rodriguez-Ibabe, I. Gutierrez, and B. Lopez, eds., Materials Science Forum Vols. 284–286, Trans Tech Publications Ltd., Aedermannsdorf, Switzerland, 1998, pp. 419–26.

    Google Scholar 

  33. I. Madariaga and I. Gutiérrez: Conf. Proc. “TRATERMAT 98,” Madrid, 1998, pp. 143–50.

  34. B.D. Cullity: Elements of X-ray Diffraction, Addison-Wesley, Reading, MA, 1978, pp. 350–68.

    Google Scholar 

  35. C.H. Macgillavry and G.D. Rieck: International Tables for X-Ray Crystallography, The Kynoch Press, Birmingham, England, 1968, vol. 3.

    Google Scholar 

  36. G. Maeder, Y. Ramon, G. Tharel, and J. Barralis: Mem. Sci. Rev. Met., 1975, pp. 397–405.

  37. G.B. Olson and W.S. Owen: New Aspects of Martensitic Transformation, Institute of Metals, Tokyo, Japan, 1976, pp. 105–10.

    Google Scholar 

  38. J.R. Yang and H.K.D.H. Bhadeshia: in Advances in Welding Science and Technology, S.A. David, ed., ASM, Metals Park, OH, 1986, pp. 187–91.

    Google Scholar 

  39. S.J. Matas and R.F. Hehemann: Trans. TMS-AIME, 1961, vol. 221, pp. 179–85.

    CAS  Google Scholar 

  40. H.K.D.H. Bhadeshia and J.W. Christian: Metall. Trans. A, 1990, vol. 21A, pp. 767–97.

    CAS  Google Scholar 

  41. H.K.D.H. Bhadeshia: Bainite in Steels. Transformations, Microstructure and Properties, The Institute of Materials, London, 1992, ch. 3.

    Google Scholar 

  42. A. Bagaryatskii: Dokl. Akad. Nauk SSSR, 1950, vol. 73, p. 1161.

    CAS  Google Scholar 

  43. W. Pitsch: Arch. Eisenhuettenwes., 1963, vol. 34, p. 381.

    CAS  Google Scholar 

  44. G.V. Kurdjumov and G. Sachs: Z. Phys., 1930, vol. 64, p. 325.

    Article  Google Scholar 

  45. H.K.D.H. Bhadeshia: Worked Examples in the Geometry of Crystals, The Institute of Metals, London, 1987.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. ITP, Parque Tecnologico de Zamudio, 48170, Vizcaya, Spain

    I. Madariaga (Researcher)

  2. Thermomechanical Treatments Group, CEIT and the University of Navarra (ESI), 20018, San Sebastian, Basque Country, Spain

    I. Gutierrez (Principal Researcher, Materials Department, and Head)

  3. the Department of Materials Science and Metallurgy, University of Cambridge, CB2 3QZ, Cambridge, United Kingdom

    H. K. D. H. Bhadeshia (Professor)

Authors
  1. I. Madariaga
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. I. Gutierrez
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. H. K. D. H. Bhadeshia
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Madariaga, I., Gutierrez, I. & Bhadeshia, H.K.D.H. Acicular ferrite morphologies in a medium-carbon microalloyed steel. Metall Mater Trans A 32, 2187–2197 (2001). https://doi.org/10.1007/s11661-001-0194-7

Download citation

  • Received:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11661-001-0194-7

Keywords

Search

Navigation