Skip to main content
Log in

High fidelity prototyping of PDMS electrophoresis microchips using laser-printed masters

  • Technical Paper
  • Published:
Microsystem Technologies Aims and scope Submit manuscript

Abstract

Toner-based fabrication technology has appeared as one of the simplest and fastest techniques to produce low-cost microfluidic devices. The instrumental simplicity and fabrication easiness make this fabrication technique quite suitable to be implemented in developing countries where the availability of resources is limited. In this study, the prototyping fidelity of poly(dimethylsiloxane) (PDMS) electrophoresis microchips has been evaluated using laser printed masters. The desirable layout of the microfluidic devices was first drawn in graphic software and then printed on the surface of transparency films by an office laser printer with 1,200-dpi resolution. The masters printed on transparency films were directly used to replicate the microfluidic structures in PDMS. The analysis of the dimensions of the printed toner lines has revealed that their thickness depends on the line width. For lines with width between 50 and 300 μm, the height ranged from 4.9 ± 0.2 to 10.4 ± 0.1 μm. The prototyping fidelity achieved for channels defined with width between 50 and 300 μm was higher than 96 %. Furthermore, it has been demonstrated that a single master can be used to replicate at least ten PDMS chips with great reproducibility. The analytical performance of the replicated PDMS microchips for electrophoresis separation has revealed good chip-to-chip and injection-to-injection reproducibility. Based on the results achieved, it is possible to conclude that toner-based masters can be a useful tool for researchers with restricted access to conventional microfabrication technologies.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5

Similar content being viewed by others

References

  • Abdelgawad M, Watson MW, Young EW, Mudrik JM, Ungrin MD, Wheeler AR (2008) Soft lithography: masters on demand. Lab Chip 8(8):1379–1385

    Article  Google Scholar 

  • Bao N, Zhang Q, Xu JJ, Chen HY (2005) Fabrication of poly(dimethylsiloxane) microfluidic system based on masters directly printed with an office laser printer. J Chromatogr A 1–2:270–275

    Article  Google Scholar 

  • Chen CS, Breslauer DN, Luna JI, Grimes A, Chin WC, Leeb LP, Khine M (2008) Shrinky-dink microfluidics: 3D polystyrene chips. Lab Chip 8(4):622–624

    Article  Google Scholar 

  • Coltro WKT, Piccin E, da Silva JAF, do Lago CL, Carrilho E (2007) A toner-mediated lithographic technology for rapid prototyping of glass microchannels. Lab Chip 7(7):931–934

    Article  Google Scholar 

  • Coltro WKT, de Jesus DP, da Silva JAF, do Lago CL, Carrilho E (2010) Toner and paper-based fabrication techniques for microfluidic applications. Electrophoresis 31(15):2487–2498

    Article  Google Scholar 

  • Coltro WKT, da Silva JAF, Carrilho E (2011) Rapid prototyping of polymeric electrophoresis microchips with integrated copper electrodes for contactless conductivity detection. Anal Methods UK 3(1):168–172

    Article  Google Scholar 

  • da Silva JAF, Guzman N, do Lago CL (2002) Contactless conductivity detection for capillary electrophoresis––hardware improvements and optimization of the input-signal amplitude and frequency. J Chromatogr A 942(1–2):249–258

    Article  Google Scholar 

  • da Silva ER, Segato TP, Coltro WKT, Lima RS, Carrilho E, Mazo LH (2013) Determination of glyphosate and AMPA on polyester-toner electrophoresis microchip with contactless conductivity detection. Electrophoresis 34(14):2107–2111

    Article  Google Scholar 

  • de Jesus DP, Blanes L, do Lago CL (2006) Microchip free-flow electrophoresis on glass substrate using laser-printing toner as structural material. Electrophoresis 27(24):4935–4942

    Article  Google Scholar 

  • de Souza FR, Alves GL, Coltro WKT (2012) Capillary-driven toner-based microfluidic devices for clinical diagnostics with colorimetric detection. Anal Chem 84(21):9002–9007

    Google Scholar 

  • do Lago CL, da Silva HDT, Neves CA, Brito-Neto JGA, da Silva JAF (2003) A dry process for production of microfluidic devices based on the lamination of laser-printed polyester films. Anal Chem 75(15):3853–3858

    Article  Google Scholar 

  • do Lago CL, Neves CA, de Jesus DP, da Silva HDT, Brito-Neto JGA, da Silva JAF (2004) Microfluidic devices obtained by thermal toner transferring on glass substrate. Electrophoresis 25(21–22):3825–3831

    Article  Google Scholar 

  • Duarte GRM, Price CW, Augustine BH, Carrilho E, Landers JP (2011) Dynamic solid phase DNA extraction and PCR amplification in polyester-toner based microchip. Anal Chem 83(13):5182–5189

    Article  Google Scholar 

  • Duffy DC, McDonald JC, Schueller OJA, Whitesides GM (1998) Rapid prototyping of microfluidic systems in poly(dimethylsiloxane). Anal Chem 70(23):4974–4984

    Article  Google Scholar 

  • Easley CJ, Benninger RKP, Shaver JH, Head WS, Piston DW (2009) Rapid and inexpensive fabrication of polymeric microfluidic devices via toner transfer masking. Lab Chip 9(8):1119–1127

    Article  Google Scholar 

  • Gabriel EFM, do Lago CL, Gobbi ÂL, Carrilho E, Coltro WKT (2013) Characterization of microchip electrophoresis devices fabricated by direct-printing process with colored toner. Electrophoresis 34(15):2169–2176

    Article  Google Scholar 

  • Grimes A, Breslauer DN, Long M, Pegan J, Lee LP, Khine M (2008) Shrinky-dink microfluidics: rapid generation of deep and rounded patterns. Lab Chip 8(1):170–172

    Article  Google Scholar 

  • Hong C, Bao D, Thomas MS, Clift JM, Vullev VI (2008) Print-and-peel fabrication of microelectrodes. Langmuir 24(16):8439–8442

    Article  Google Scholar 

  • Jena RK, Yue CY, Lam YC, Tang PS, Gupta A (2012) Comparison of different molds (epoxy, polymer and silicon) for microfabrication by hot embossing technique. Sens Actuator B Chem 163(1):233–241

    Article  Google Scholar 

  • Kaigala GV, Ho S, Penterman R, Backhouse CJ (2007) Rapid prototyping of microfluidic devices with a wax printer. Lab Chip 7(3):384–387

    Article  Google Scholar 

  • Kuban P, Hauser PC (2013) Contactless conductivity detection for analytical techniques: developments from 2010 to 2012. Electrophoresis 34(1):55–69

    Article  Google Scholar 

  • Liu AL, He FY, Wang K, Zhou T, Lu Y, Xia XH (2005) Rapid method for design and fabrication of passive micromixers in microfluidic devices using a direct-printing process. Lab Chip 5(9):974–978

    Article  Google Scholar 

  • Lu Y, Hu YL, Xia XH (2009) Effect of surface microstructures on the separation efficiency of neurotransmitters on a direct-printed capillary electrophoresis microchip. Talanta 79(5):1270–1275

    Article  Google Scholar 

  • McDonald JC, Duffy DC, Anderson JR, Chiu DT, Wu HK, Schueller OJA, Whitesides GM (2000) Fabrication of microfluidic systems in poly(dimethylsiloxane). Electrophoresis 21(1):27–40

    Article  Google Scholar 

  • McDonald JC, Chabinyc ML, Metallo SJ, Anderson JR, Stroock AD, Whitesides GM (2002) Prototyping of microfluidic devices in poly(dimethylsiloxane) using solid-object printing. Anal Chem 74(7):1537–1545

    Article  Google Scholar 

  • Ouyang Y, Wang S, Li J, Riehl PS, Begley M, Landers JP (2013) Rapid patterning of ‘tunable’ hydrophobic valves on disposable microchips by laser printer lithography. Lab Chip 13(9):1762–1771

    Article  Google Scholar 

  • Tan AM, Rodgers K, Murrihy JP, O’Mathuna C, Glennon JD (2001) Rapid fabrication of microfluidic devices in poly(dimethylsiloxane) by photocopying. Lab Chip 1(1):7–9

    Article  Google Scholar 

  • Thomas M, Millare B, Clift JM, Vullev VI (2009) Print-and-peel fabrication for microfluidics. Abstr Papers Am Chem Soc 237:263

    Google Scholar 

  • Thomas MS, Millare B, Clift JM, Bao D, Hong C, Vullev VI (2010) Print-and-peel fabrication for microfluidics: what’s in it for biomedical applications? Ann Biomed Eng 38(1):21–32

    Article  Google Scholar 

  • Vullev VI, Wan JD, Heinrich V, Landsman P, Bower PE, Xia B, Millare B, Jones G (2006) Nonlithographic fabrication of microfluidic devices. J Am Chem Soc 128(50):16062–16072

    Article  Google Scholar 

  • Yu H, He FY, Lu Y, Hu YL, Zhong HY, Xia XH (2008a) Improved separation efficiency of neurotransmitters on a native printed capillary electrophoresis microchip simply by manipulating electroosmotic flow. Talanta 75(1):43–48

    Article  Google Scholar 

  • Yu H, Lu Y, Zhou YG, Wang FB, He FY, Xia XH (2008b) A simple, disposable microfluidic device for rapid protein concentration and purification via direct-printing. Lab Chip 8(9):1496–1501

    Article  Google Scholar 

Download references

Acknowledgments

This project has been supported by Conselho Nacional de Desenvolvimento Científico e Tecnólogico (CNPq)—Grant 478911/2012-2––and Fundação de Amparo à Pesquisa do Estado de Goiás (FAPEG). The authors gratefully acknowledge the research fellowships granted from CNPq to D. P. J. (Grant No. 305318/2012-8) and W. K. T. C. (Grant No. 311744/2013-3) and scholarships granted from CNPq to E. O. L. and L. C. D. and from CAPES to L. E. P. B. We would like to thank the Laboratory of Microfabrication from Brazilian Nanotechnology Laboratory for using their facilities.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Wendell Karlos Tomazelli Coltro.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lobo Júnior, E.O., Duarte, L.C., Paula Braga, L.E. et al. High fidelity prototyping of PDMS electrophoresis microchips using laser-printed masters. Microsyst Technol 21, 1345–1352 (2015). https://doi.org/10.1007/s00542-014-2190-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00542-014-2190-z

Keywords

Navigation