Abstract
Thermoplastic hybrid composites offer a huge potential for lightweight design but due to the complex process chain for their manufacturing, the needed production plants often are quite expensive resulting in a profitability only for large lot sizes. A modular plant architecture allows a more flexible production of different parts thanks to reconfigurability. This results in cost savings which enable economical manufacturing of smaller lot sizes. In the following paper an approach for a modular production plant for thermoplastic hybrid composites and its architecture is presented. The modules of the plant are standard machines with a uniform interface linked by OPC UA. The core is a line control module controlling the sequence of production steps, plant safety and visualization. The independent control system of the production modules is based on a service-oriented architecture and state-based control. For the engineering of the plant, an approach for fast configuration and reconfiguration is presented. Using a self-developed web application the plant can be easily configured resulting in a so called production recipe containing all the relevant information about the plant. The production recipe is imported by a code generator, which automatically converts the information in a PLC code for operation of the line control. The described approach is validated by building and commissioning two different configurations of the production plant showing the feasibility of the concept and significant gains in commissioning time.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Henning F, Kuppinger J, Paul H (2012) Examining technologies for composite hybrids—a multi-material approach to eliminate joining and assembly barriers impacting performance. Global Automotive Lightweight Materials, Detroit
Fleischer J, Teti R, Lanza G et al (2018) Composite materials parts manufacturing. CIRP Ann 67(2):603–626. https://doi.org/10.1016/j.cirp.2018.05.005
Janssen H, Peters T, Brecher C (2017) Efficient production of tailored structural thermoplastic composite parts by combining tape placement and 3d printing. Proc CIRP 66:91–95. https://doi.org/10.1016/j.procir.2017.02.022
Kropka M, Muehlbacher M, Neumeyer T et al (2017) From UD-tape to final part—a comprehensive approach towards thermoplastic composites. Proc CIRP 66:96–100. https://doi.org/10.1016/j.procir.2017.03.371
Krüger J, Wang L, Verl A et al (2017) Innovative control of assembly systems and lines. CIRP Ann 66(2):707–730. https://doi.org/10.1016/j.cirp.2017.05.010
Holm T, Obst M, Ladiges J et al (2016) Namur Modul Type Package—Implementierung. atp Ed 58:82. https://doi.org/10.17560/atp.v58i01-02.555
Bernshausen J, Haller A, Holm T et al (2016) Namur Modul Type Package—Definition. atp Ed 58:72. https://doi.org/10.17560/atp.v58i01-02.554
Wassilew S, Urbas L, Ladiges J et al (2016) Transformation of the NAMUR MTP to OPC UA to allow plug and produce for modular process automation. In: 2016 IEEE 21st international conference on emerging technologies and factory automation (ETFA): September 6–9, 2016 Berlin, Germany. IEEE, Piscataway, NJ, pp 1–9
Dosch S, Spohrer A, Fleischer J (2015) Reduced commissioning time of components in machine tools through electronic data transmission. Proc CIRP 29:311–316. https://doi.org/10.1016/j.procir.2015.02.198
Bloch H, Fay A, Hoernicke M (2016) Analysis of service-oriented architecture approaches suitable for modular process automation. In: 2016 IEEE 21st international conference on emerging technologies and factory automation (ETFA): September 6–9, 2016 Berlin, Germany. IEEE, Piscataway, NJ, pp 1–8
Bloch H, Fay A, Knohl T et al (2017) A microservice-based architecture approach for the automation of modular process plants. In: 2017 22nd IEEE international conference on emerging technologies and factory automation (ETFA), pp 1–8
Albers T, Otten W, Haller A et al (2015) Modulare Produktion—Auswirkungen auf die Automatisierung. Etz—Elektrotechnik & Automation 2015(11)
International Electrotechnical Commission (1997) Batch control—Part 1: models and terminology. ICS 25.040.40 (IEC 61512-1)
Huffman DA (2009) Benefits of state based control: white paper
Bloch H, Hensel S, Hoernicke M et al (2018) State-based control of process services within modular process plants. Proc CIRP 72:1088–1093. https://doi.org/10.1016/j.procir.2018.03.037
Strasser T, Zoitl A, Christensen JH et al (2011) Design and execution issues in IEC 61499 distributed automation and control systems. IEEE Trans Syst Man Cybern C41(1):41–51. https://doi.org/10.1109/TSMCC.2010.2067210
International Electrotechnical Commission (2014) Engineering data exchange format for use in industrial automation systems engineering—Automation markup language—part 1: architecture and general requirements (62714-1)
Himmler F (2015) Function based engineering with automationML: Towards better standardization and seamless process integration in plant engineering. In: Thomas O, Teuteberg F (eds) 12 International Tagung Wirtschaftsinformatik pp 16–30
Acknowledgements
This paper is based on investigations within the research grant supported by the Federal Ministry of Education and Research (Project number 02P14A178) and supervised by the project management agency PTKA.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Moll, P., Schäfer, M., Coutandin, S. et al. Reconfigurable modular production plant for thermoplastic hybrid composites. Prod. Eng. Res. Devel. 13, 469–477 (2019). https://doi.org/10.1007/s11740-019-00898-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11740-019-00898-z