Extraction of extracellular polymers from activated sludge using a cation exchange resin

doi:10.1016/0043-1354(95)00323-1

Water Research

Volume 30, Issue 8, August 1996, Pages 1749-1758

https://doi.org/10.1016/0043-1354(95)00323-1 Get rights and content

Abstract

The extraction of water soluble extracellular polymeric substances (EPS) from activated sludge was investigated. The extraction procedure was based upon cation exchange using a cation exchange resin (CER). Activated sludge from two different types of treatment plants responded very similarly to the extraction procedure. The EPS yield was enhanced by increasing the stirring intensity, the amounts of CER added and by increasing the extraction time. For the chosen extraction procedure the yield was twice as high as other commonly used procedures. The extract consisted mainly of protein but also humic compounds, carbohydrates, uronic acids and DNA were found in significant amounts. The extracted amounts and relative fraction of the individual compounds strongly depended on how the extraction was performed. The ratio between protein and carbohydrate was found in the range 3.9–5.1 depending on the extraction time. Humic compounds and DNA were the compounds most easily extracted. HPSEC investigation of the extract revealed that the extraction did not significantly degrade the EPS. Some cell lysis was identified during the extraction for extraction times greater than 1–2 h by observing a decrease in cell number (stained by DAPI, CTC and acridine orange). The lysis was not considered a significant problem for contaminating the EPS. Measurements of the cell number and cell size distribution in the sludge suggested that the cell mass did not account for more than approximately 10–15% of the total organic fraction of the investigated sludge. Two extraction strategies were formulated. One for a very gentle and one for a very effective method. Analytical methods for analysis of sludge and EPS extracts were compared and discussed. A corrected Lowry method for analyzing protein as well as humic compounds was implemented and found suitable.

References (50)

N. Blumenkrantz et al.
A new method for quantitative determination of uronic acids
Anal. Bio.
(1973)
M.M. Bradford
A rapid and sensitive method for the quantitation of microgram quantities of protein utilizing the principle of protein-dye binding
Analyt. Biochem.
(1976)
C.F. Brunk et al.
Assay for nanogram quantities of DNA in cellular homogenates
Analyt. Biochem.
(1979)
T.E. Cloete et al.
A combined membrane filter-immunofluorescent technique for the in situ identification and enumeration of Acinetobacter in activated sludge
Water Res.
(1988)
J.H. Bruus et al.
On the stability of activated sludge flocs with implication to dewatering
Water Res.
(1992)
R. Gehr et al.
Removal of extracellular material, techniques and pitfalls
Water Res.
(1983)
J.A.S. Goodwin et al.
A further examination into the composition of activated sludge surfaces in relation to their settlement characteristics
Water Res.
(1985)
N. Horan et al.
Purification and characterization of extracellular polysaccharides from activated sludge
Water Res.
(1986)
S.-M. Kang et al.
Properties of extracellular polymers having an effect on expression of activated sludge
J. Ferm. Bioeng.
(1990)
J.W. Morgan et al.
A comparative study of the nature of biopolymers extracted from anaerobic and activated sludge
Water Res.
(1990)

S. Nishikawa et al.

Nucleic acid as a component of mucilage in activated sludge

Water Res.

(1968)

S. Okabe et al.

Estimation of cellular and and extracellular carbon content in sulfate-reducing bacteria biofilms by lipopolysaccharide assay and epifluorescence microscopic technique

Water Res.

(1994)

H. Rasmussen et al.

Observations on dewaterability and physical, chemical and microbiological changes in anaerobically stored activated sludge from a nutrient removal plant

Water Res.

(1994)

K. Raunkjær et al.

Measurement of pools of protein, carbohydrate and lipid in domestic wastewater

Water Res.

(1994)

R. Riffaldi et al.

Humic substances in sewage sludges

Environ. Pollut.

(1982)

V. Urbain et al.

Bioflocculation in activated sludge: analytical approach

Water Res.

(1993)

J.K. Vallom et al.

Lysis as a factor in sludge flocculation

Water Res.

(1984)

APHA et al.

Standard Methods for the Examination of Water and Wastewater

(1992)

J.B. Barber et al.

Evaluation of biological sludge properties influencing volume reduction

J. Water Pollut. Cont. Fed.

(1986)

J.D. Box

Investigation on the Folin-Ciocalteau phenol reagent for determination of polyphenolic substances in natural waters

Water Res.

(1983)

M.J. Brown et al.

Comparison of bacterial extracellular polymer extraction methods

Appl. Environ. Microbiol.

(1980)

J.R. Christensen

A systematic approach to characterization of sludge conditioning and dewatering

M. Dubois et al.

Colorimetric method for determination of sugars and related substances

Analyt. Chem.

(1956)

L. Eriksson et al.

Study of flocculation mechanisms by observing effects of a complexing agent on activated sludge properties

Water Sci. Technol.

(1991)

L. Eriksson et al.

Settling properties of activated sludge related to floc structure

Water Sci. Technol.

(1984)

Cited by (2257)

Evaluation of the shear stability of aerobic granular sludge from a pilot-scale membrane bioreactor: Establishment of a quantitative method
2025, Journal of Environmental Sciences (China)
This work established a quantitative method to access the shear stability of aerobic granular sludge (AGS) and validated its feasibility by using the mature AGS from a pilot-scale (50 tons/day) membrane bioreactor (MBR) for treating real municipal wastewater. The results showed that the changing rate (ΔS) of the peak area (S) of granule size distribution (GSD) exhibited an exponential relationship (R²≥0.76) with the shear time ( $y = a - b \cdot c^{x}$ ), which was a suitable indicative index to reflect the shear stability of different AGS samples. The limiting granule size (LGS) was defined and proposed to characterize the equilibrium size for AGS after being sheared for a period of time, whose value in terms of Dv50 showed high correlation (R²=0.92) with the parameter a. The free Ca²⁺ (28.44–34.21 mg/L) in the influent specifically interacted with polysaccharides (PS) in the granule's extracellular polymeric substance (EPS) as a nucleation site, thereby inducing the formation of Ca precipitation to enhance its Young's modulus, while Ca²⁺ primarily interacted with PS in soluble metabolic product (SMP) during the initial granulation process. Furthermore, the Young's modulus significantly affected the parameter a related to shear stability (R²=0.99). Since the parameter a was more closely related (R²=1.00) to ΔS than that of the parameter b or c, the excellent correlation (R²=0.99) between the parameter a and the wet density further verified the feasibility of this method.
Effect of gradual increase of salt on performance and microbial community during granulation process
2025, Journal of Environmental Sciences (China)
Salinity was considered to have effects on the characteristics, performance microbial communities of aerobic granular sludge. This study investigated granulation process with gradual increase of salt under different gradients. Two identical sequencing batch reactors were operated, while the influent of Ra and Rb was subjected to stepwise increments of NaCl concentrations (0–4 g/L and 0–10 g/L). The presence of filamentous bacteria may contribute to granules formed under lower salinity conditions, potentially leading to granules fragmentation. Excellent removal efficiency achieved in both reactors although there was a small accumulation of nitrite in Rb at later stages. The removal efficiencies of chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) in Ra were 95.31%, 93.70% and 88.66%, while the corresponding removal efficiencies in Rb were 94.19%, 89.79% and 80.74%. Salinity stimulated extracellular polymeric substances (EPS) secretion and enriched EPS producing bacteria to help maintain the integrity and stability of the aerobic granules. Heterotrophic nitrifying bacteria were responsible for NH₄⁺-N and NO₂⁻-N oxidation of salinity systems and large number of denitrifying bacteria were detected, which ensure the high removal efficiency of TN in the systems.
Efficient extraction of Au(Ⅲ) by a piperidine-based ionic liquid and exploration of the mechanism driving force
2024, Separation and Purification Technology
Efficient gold extraction is of paramount importance, but how to improve the extraction efficiency and enhance the driving force of the extraction process is still to be explored. This study introduces an innovative approach using versatility ionic liquids (ILs) to overcome existing challenges. A tailored IL was synthesized and employed computational tools, including the Interaction Region Indicator, to predict its effectiveness in gold extraction. Quantum chemical calculations elucidated the interplay between hydrogen bonding capability and ion exchange properties of the ILs. Subsequent optimization of experimental conditions (0.1 mol/L HCl, 10.6 mg IL) yielded a remarkable 98.4 % extraction efficiency at 45 °C. Molecular dynamics simulations affirmed the IL's exceptional selectivity for Au(III) extraction, with analysis revealing that the extraction mechanism primarily hinged on electrostatic attraction and van der Waals interactions between ionic liquid cations and [AuCl₄]⁻. This mechanism aligns with the established anion exchange mechanism, validated through Ultraviolet–visible spectrometer (UV–Vis), Nuclear Magnetic Resonance spectrometer (NMR), and Liquid Chromatograph Mass Spectrometer (LC-MS) analyzes. To complete the extraction cycle, 1.0 mol/L K₂C₂O₄ was employed as a stripping agent for efficient Au(III) recovery from the loaded IL phase, facilitating repeated extraction cycles. This study underscores the sustainability of the IL-based Au(III) extraction process, maintaining consistently high extraction rates even after five cycles. In summary, this method does not use solvent, enabling environmentally friendly Au(III) extraction.
The Structure of the Cannibal Sludge flocs generated under the fast and the slow feed conditions and their Digestibility
2024, Case Studies in Chemical and Environmental Engineering
An activated sludge system that incorporates a sidestream anaerobic bioreactor, called the Cannibal process, generated about 60 % less solids than conventional activated sludge without any negative effects on the effluent quality. In addition, operating the Cannibal process with different feeding patterns can result in different system performance. When the feed is provided to the Cannibal system over a period of 5 minutes (fast feed), the system generates less solid than the Cannibal system fed over a period of 4 hours (slow feed). In this study, the cation exchange resin (CER) and sulfide addition procedures were utilized to extract the Cannibal sludge flocs generated under the fast and the slow feed conditions to gain a fundamental insight on the structure and their components of those flocs. In addition, the fast and the slow feed Cannibal sludge was anaerobically and aerobically digested to evaluate the effect of feeding patterns on their digestibility. It was found that the readily biodegradable (1 kDa.) CER and sulfide extracted protein is larger in the flocs from the fast feed than the slow feed Cannibal system. When these two different types of flocs were anaerobically digested, the major fractions to be degraded were the sulfide extractable proteins. It was also found that the proteins in the fast feed Cannibal sludge flocs were degraded more than that in the slow feed Cannibal sludge flocs under anaerobic conditions. Consequently, it can be proposed that the influence of the high substrate pressure (fast feed) is to generate larger readily biodegradable proteins in the fast feed than the slow feed Cannibal sludge flocs. Because the 1 kDa. sulfide extracted proteins released from the fast feed Cannibal sludge floc are more biodegradable than that from the slow feed Cannibal sludge under anaerobic environment, it can be thought that the 1 kDa. proteins generated under the fast feed condition may consist of either many simple amino acids that are easily degradable or amino acids that microorganisms cannot produce but need to consume for their survival.
Integrative chemical and multiomics analyses of tetracycline removal mechanisms in Pseudomonas sp. DX-21
2024, Journal of Hazardous Materials
Tetracycline (TC), widely found in various environments, poses significant risks to ecosystems and human health. While efficient biodegradation removes TC, the mechanisms underlying this process have not been elucidated. This study investigated the molecular mechanisms underlying TC biosorption and transfer within the extracellular polymeric substances (EPS) of strain DX-21 and its biodegradation process using fourier transform infrared spectroscopy, molecular docking, and multiomics. Under TC stress, DX-21 increased TC biosorption by secreting more extracellular polysaccharides and proteins, particularly the latter, mitigating toxicity. Moreover, specialized transporter proteins with increased binding capacity facilitated TC movement from the EPS to the cell membrane and within the cell. Transcriptomic and untargeted metabolomic analyses revealed that the presence of TC led to the differential expression of 306 genes and significant alterations in 37 metabolites. Notably, genes related to key enzymes, such as electron transport, peroxidase, and oxidoreductase, exhibited significant differential expression. DX-21 combated and degraded TC by regulating metabolism, altering cell membrane permeability, enhancing oxidative defense, and enhancing energy availability. Furthermore, integrative omics analyses indicated that DX-21 degrades TC via various enzymes, reallocating resources from other biosynthetic pathways. These results advance the understanding of the metabolic responses and regulatory mechanisms of DX-21 in response to TC.
Mechanistic insights into chemical conditioning on transformation of dissolved organic matter and plant biostimulants production during sludge aerobic composting
2024, Water Research
Inorganic coagulants (aluminum and iron salt) are widely used to improve sludge dewaterability, resulting in numerous residues in dewatered sludge. Composting refers to the controlled microbial process that converts organic wastes into fertilizer, and coagulant residues in dewatered sludge can affect subsequent compost efficiency and resource recycling, which remains unclear. This work investigated the effects of two typical metal salt coagulants (poly aluminum chloride [PAC] and poly ferric sulfate [PFS]) conditioning on sludge compost. Our results revealed that PAC conditioning inhibited composting with decreased peak temperature, microbial richness, enzymatic reaction intensities, and compost quality, associated with decreased pH and microbial toxicity of aluminum. Nevertheless, PFS conditioning selectively enriched Pseudoxanthomonas sp. and resulted in more fertile compost with increased peak temperature, enzymatic reaction intensities, and humification degree. Spectroscopy and mass difference analyses indicated that PFS conditioning enhanced reaction intensities of labile biopolymers at the thermophilic stage, mainly comprising hydrolyzation (H₂O), dehydrogenation (-H₂, -H₄), oxidation (+O₁H₂), and other reactions (i.e., +CH₂, C₂H₄O₁, C₂H₆O₁). Unlike the common composting process primarily conducts humification at the cooling stage, PFS conditioning changed the main occurrence stage to the thermophilic stage. Non-targeted metabolomics revealed that indole (a humification intermediate) is responsible for the increased humification degree and indoleacetic acid content in the PFS-conditioned compost, which then promoted compost quality. Plant growth experiments further confirmed that the dissolved organic matter (DOM) in PFS-conditioned compost produced the maximum plant biomass. This study provided molecular-level evidence that PFS conditioning can promote humification and compost fertility during sludge composting, enabling chemical conditioning optimization for sustainable management of sludge.

View all citing articles on Scopus

^∗: Present address: Danish Technological Institute, Teknologiparken, DK-8000 Arhus, Denmark.

View full text

Extraction of extracellular polymers from activated sludge using a cation exchange resin

Abstract

Anal. Bio.

Analyt. Biochem.

Analyt. Biochem.

Water Res.

Water Res.

Water Res.

Water Res.

Water Res.

J. Ferm. Bioeng.

Water Res.

Water Res.

Water Res.

Water Res.

Water Res.

Environ. Pollut.

Water Res.

Water Res.

Standard Methods for the Examination of Water and Wastewater

Evaluation of biological sludge properties influencing volume reduction

J. Water Pollut. Cont. Fed.

Investigation on the Folin-Ciocalteau phenol reagent for determination of polyphenolic substances in natural waters

Water Res.

Comparison of bacterial extracellular polymer extraction methods

Appl. Environ. Microbiol.

A systematic approach to characterization of sludge conditioning and dewatering

Colorimetric method for determination of sugars and related substances

Analyt. Chem.

Study of flocculation mechanisms by observing effects of a complexing agent on activated sludge properties

Water Sci. Technol.

Settling properties of activated sludge related to floc structure

Water Sci. Technol.