Effect of synthesis pH on the structure of carbon xerogels
Abstract
Mesoporous carbon xerogels were prepared from the sol-gel polymerization of resorcinol with formaldehyde (RF) followed by carbonization. The effect of the initial pH of the RF solution on the surface area, pore volume, pore size distribution and nanostructure was studied. A brief mechanism of polymerization is discussed. Typically, a lower initial pH yielded carbon xerogels with a higher surface area and pore volume, and a broader pore size distribution. The highest surface area and pore volume were around 620 m2 g−1 and 0.8 cm3 g−1, with a mean pore radius ranging from 4 to 6 nm and with 80% of the pore volume as mesopores. Transmission electron microscopy and X-ray diffraction revealed a surface morphology consisting of 10 nm diameter particles randomly oriented to produce a partially nanocrystalline structure in between graphite and activated carbon. Thermogravimetric and differential scanning calorimetric analyses disclosed a significant weight loss (50%) during a strongly exothermic carbonization process.
References (29)
- S. Sircar et al.
Carbon
(1996) - Y.H. Liu et al.
Carbon
(1996) - Y. Ein-Eli et al.
Electrochimica Acta
(1994) - H. Shi
Electrochimica Acta
(1996) - I. Tanahashi et al.
Carbon
(1991) - P.J. Davis et al.
J. Non-Cryst. Solids
(1992) - H.A. Yu et al.
Carbon
(1996) - A. Mabuchi et al.
J. Electrochem. Soc.
(1995) - T. Zheng et al.
J. Electrochem. Soc.
(1995) - M. Aoki et al.
IEICE Trans. Fundamentals
(1994)
J. Electrochem. Soc.
Bull. Chem. Soc. Jpn.
Bull. Chem. Soc. Jpn.
Cited by (346)
Ionothermal synthesis of fiber-reinforced carbon aerogel composites from fructose with high mechanical and thermal insulation properties
2024, Composites Part A: Applied Science and ManufacturingIn this work, carbon fiber reinforced biomass carbon aerogel composites (CF/CA) were prepared by ionothermal synthesis using fructose as the raw material and oxidized polyacrylonitrile fiber as the reinforcing agent. During the preparation process, we have mixed fructose with oxidized polyacrylonitrile fibers and subjected them to a carbonization process under the conditions of hot ionic liquids. By controlling the reaction conditions, we successfully prepared fiber-reinforced carbon aerogel composites with excellent properties. The CF/CA has a high compressive strength (3.306 MPa). At the same time, the original low thermal conductivity (0.106 W·m−1·K−1) and low density (0.2976 g/cm2) of the carbon aerogel are maintained. In this work, the mechanical properties of carbon aerogel are improved to 230 % without changing the thermal insulation properties of CA, which makes a certain progress compared with the similar research. These excellent properties make CF/CA a promising engineering material. Moreover, we found that about 95 % of the ionic liquid can be recovered by evaporating under reduced pressure, and the recovered ionic liquid is still usable. This discovery provides a possibility for the green and sustainable development of the preparation process of carbon aerogels. This study provides new ideas and methods to further optimize the properties and applications of biomass carbon aerogels and their composites.
4-Hydroxybenzenesulfonic acid triggers rapid preparation of phenolic aerogel composites by ambient pressure drying
2024, Chemical Engineering JournalPhenolic aerogel composites, as an excellent thermal insulation material, have been used in aerospace to resist extreme working conditions of severe heating and intense mechanical stress. However, the high cost and lengthy preparation process seriously restricts their more extensive application. Herein, a novel strategy for rapid preparation of aerogel composites by ambient pressure drying is enabled by copolymerization with 4-hydroxybenzenesulfonic acid. That is, the reactive 4-hydroxybenzenesulfonic acid can serve as the acid catalyst to accelerate both the protonation step and the gelation step during the preparation process of phenolic aerogel. After copolymerization with 4-hydroxybenzenesulfonic acid, these sulfonic acid groups significantly accelerate the protonation of benzoxazine intermediates, leading to more carbocation formation. The activation energy of curing reaction is significant decreased from 300 kJ∙mol−1 to 90 kJ∙mol−1. Thus, 4-hydroxybenzenesulfonic acid containing phenol formaldehyde resin (PFS) aerogel precursors exhibit much faster gelation reaction (within 4 h) than phenol formaldehyde resin (PF) aerogel precursor (12 h), which further facilitates the preparation of phenolic aerogel composites with needled quartz fiber felt by ambient pressure drying. Importantly, the PFS aerogel composites exhibit excellent thermal insulation performance under low heat flux and good fire safety under high heat flux. Rapid gelation of PFS triggered by 4-hydroxybenzenesulfonic acid provides a new approach to develop phenolic aerogel composites with low energy consumption, low cost and short preparation cycle.
Sustainable development of pulping by-product for limiting its pollution risk and production new aerogel-based carbon nanostructures for dyes adsorption
2023, Journal of Cleaner ProductionA clean approach for disposing the pulping by-product (black liquors- BLs) as an effective component in preparing high surface area aerogel-based carbon nanostructure adsorbents was the objective of this current work. These novel adsorbents were assessed as a benefit for removing the cationic and anionic dyes. In this respect, black liquors from pulping of rice straw by different pulping reagents were used as components together with resorcinol in production of aerogel precursors for carbon nanostructures (CNSs). The effective role of BL-based aerogels was evidenced from comparing their CNSs adsorption capacities with CNSs of aerogels free from BLs, towards dyes together with iodine. Different isotherms (Langmuir, Freundlich, Temkin and Dubinin-radushkevich (D-R) were studied to calculate the adsorption capacities. Results showed that CNSs from BL-based aerogels had higher adsorption capacities to dyes (methylene blue (MB) and brilliant blue (BB) than that produced in absence of BLs; where it increased from 256 to 307 mg/g and from 7 to 61 mg/g, respectively. The BLs from pulping of RS with alkaline reagents (NaOH and KOH–NH4OH) provided highest MB adsorbents, while highest adsorption of BB was noticed in case of BL from sulfite reagent, moreover this BL only provided improvement in Iodine value (increased from 752 to 968 mg/g). It is interesting to note that with this investigation we are able to overcome the problems of obtaining carbon nanomaterials from BLs or extracted lignin with low surface area. The surface area of the CNSs that produced through our investigation (1607 m2/g) surpassed the results from previous published work.
Towards selective synthesis of quinoxalines by using transition metals-doped carbon aerogels
2023, Catalysis TodayTransition metal (TM)-carbon aerogels, where TM = Mo, Fe, Co or Cu, were found to be active and selective catalysts for the synthesis of quinoxalines 1, from o-phenylenediamine 2 and α-hydroxy ketones 3, becoming an efficient and sustainable alternative to other carbon-based catalysts or even MOF.
Doping metal phase consisting of the corresponding metal oxides but also as zero-valent metals depending on the metal and carbonization temperature, and metal loading at the surface of carbon aerogel are key factors conditioning both reactivity and selectivity. Although metal oxides are probably the predominant active catalytic species, zero-valent metals nanoparticles (Cu0 or Co0) could be implied in the last dehydrogenation step of the reaction. Moreover, the additional functionalization with oxygenated surface groups (Co-1000PO catalyst) resulted on an enhanced reactivity probably due to the cooperation between both functions. Remarkably, Mo-500 catalyst was the most efficient sample selectively leading to the quinoxaline 1a in high conversion.
Finally, our results strongly suggest different operative pathways when using TM-doped carbon aerogels depending on the metallic phase at the carbon surface. While TM-doped carbon aerogels (where TM = Fe, Co, or Cu) probably act catalyzing a sequential acid-base steps and subsequent aromatization leading to the corresponding quinoxaline 1a, Mo-doped catalyst would work via the initial oxidation of α-hydroxy ketones followed by condensation-dehydration reactions.
Electrochemical performance of supercapacitor electrodes based on carbon aerogel-reinforced spread tow carbon fiber fabrics
2023, Composites Science and TechnologyFabric-based supercapacitor electrodes were fabricated by embedding spread tow carbon fiber fabrics, in monolithic, bicontinuous carbon aerogels (CAG). The incorporation of CAG, at less than 30 wt%, increased the specific surface area of the CAG-CF fabric to above 230 m2 g−1 and the pore volume to about 0.35 cm3 g−1, orders of magnitude higher than that for the as-received carbon fibres. The presence of the CAG not only improves the electrochemical performance of the composite electrodes but may enhance the mechanical response due to the high stiffness of the aerogel structure. Cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance measurements were performed on symmetric supercapacitor cells consisting of two CAG-reinforced fabrics in an ionic liquid electrolyte. The specific capacitance of the symmetric supercapacitor was determined to be in the range 3–5 F g−1, considerably higher than that for the plain carbon fibers. Since optimum structural electrolytes are not yet available, this value was normalized to the total mass of both electrodes to place an upper bound on future structural supercapacitors using this spread tow CAG-CF system. The maximum specific energy and specific power, normalized to the total mass of the electrodes, were around 2.64 W h kg−1 and 0.44 kW kg−1, respectively. These performance metrics demonstrate that the thin CAG-modified spread tow fabrics are promising electrodes for future use in structural supercapacitors. In principle, in future devices, the reduced ply thickness offers both improved mechanical properties and shorter ion diffusion distance, as well as opportunities to fabricate higher voltage multicell assemblies within a given component geometry.
Frontiers and recent developments on supercapacitor's materials, design, and applications: Transport and power system applications
2023, Journal of Energy StorageIn this ever increasing energy-dependent globe, energy storage devices perform an important role in reducing dependency on fossil fuels. Supercapacitors end-to-end with rechargeable batteries can be used to afford supplementary power required for various purposes, e.g., electric vehicles and hybrid electric vehicles. Supercapacitors have attracted significant interest due to their rate of charge-discharge, long cyclability, and high power-density. However, there are multiple challenges that need to be resolved, of which the most urgent are the research and development of active electrode materials and electrolytes that need to be studied using new materials with desirable properties for energy device applications.
This review provides an in-depth analysis of various areas that cover the state-of-art progress of supercapacitors and their applications in various fields, including transport and power systems. Firstly, we provide a brief introduction to important details of supercapacitors, and their types, followed by an in-depth discussion of various active electrodes based on carbons, conducting polymers, and transition metal-oxides, and then presenting the comprehensive studies of various electrolytes consisting of liquid and polymer-based electrolytes with their different classes and remarkable electrochemical properties. The electrode and electrolyte materials of supercapacitors are discussed with respective electrochemical analyses tabulated based on fundamental and ultimately targeting various properties and desirable behavior. We discuss new findings on supercapacitor mechanisms and designs followed by providing a comprehensive overview focusing on the new active electrode materials for supercapacitors. The descriptive demonstration of new devices for supercapacitors and micro-supercapacitors designs with their different types is presented. The supercapacitor applications in various transport and power fields are also touched upon systematically. Finally, the challenges and future opportunities of this promising supercapacitor field for advanced and emerging applications are included.