Abstract
The effect of welding processes such as shielded metal arc welding, gas metal arc welding and gas tungsten arc welding on tensile and impact properties of the ferritic stainless steel conforming to AISI 409M grade is studied. Rolled plates of 4 mm thickness were used as the base material for preparing single pass butt welded joints. Tensile and impact properties, microhardness, microstructure and fracture surface morphology of the welded joints have been evaluated and the results are compared. From this investigation, it is found that gas tungsten arc welded joints of ferritic stainless steel have superior tensile and impact properties compared with shielded metal arc and gas metal arc welded joints and this is mainly due to the presence of finer grains in fusion zone and heat affected zone.
Similar content being viewed by others
References
Salhiya P. Aravindan S, Noorul Haq A. Effect of Friction Welding Parameters on Mechanical and Metallurgical Proper-lies of Ferritic Stainless Steel [J]. International Journal of Advanced Manufacturing Technology, 2007, 31: 1076.
Folkhard E. Welding Metallurgy of Stainless Steels [M]. New York: Spring-Verlag Wien, 1988.
Martin van Warmelo, David Nolan. John Norrish. Mitigation of Sensitisation Effects in Unstabilised 12%Cr Ferritic Stainless Steel Welds [J]. Materials Science and Engineering. 2007. 464A (1–2): 157.
Villafuerte J C, Kerr H W. Grain Structures in Gas Tungsten Arc Welds of Austenilic Stainless Steels With Ferrite Primary Phase [J]. Metallurgical Transactions, 1990, 21A: 979.
Villafuerte J C, Kerr H W. David S A. Mechanisms of Equiaxed Grain Formation in Ferritic Stainless Steel Gas Tungsten Arc Welds [J]. Material Science and Engineering. 1995. 194A (1): 187.
Mohandas T. Madhusudhan Reddy G. Mohammad Naveed. A Comparative Evaluation of Gas Tungsten and Shielded Metal Arc Welds of a Ferritic Stainless Steel [J]. Journal of Materials Processing Technology. 1999, 94: 133.
Meyers A M, M du Toit. Interstitial Diffusion of Carbon and Nitrogen Into Heal Affected Zones of 11–12% Chromium Steel Welds [J]. Welding Research Supplement, 2001, 80 (12): 275.
Cleiton C Silva, Jesualdo P Farias, Helio C Miranda, et al. Microstruclural Characterization of the HAZ in AISI 444 Ferritic Stainless Steel Welds [J]. Materials Characterization, 2008, 59 (5): 528.
Balasubramanian V, Shanmugam K, Lakshminarayanan A K. Tensile and Impact Properties of Shielded Melal Arc Welded Ferritic Stainless Steel Joints [J]. Journal of Materials Science and Technology, China, 2009, 25(2): 1.
Potluri N B, Ghosh P K, Gupta P C, et al. Studies on Weld Metal Characteristics and Their Influences on Tensile and Fatigue Properties of Fatigue Properties of Pulsed Current GMA Welded Al-Zn-Mg Alloy [J]. Welding Research Supplement, 1996, 75: 62s.
Norman A F, Drazhner V, Prangnell P B. Effect of Welding Parameters on the Solidification Microstructure of Autogenous TIG Welds in an Al-Cu-Mg-Mn Alloy [J]. Material Science and Engineering. 1999, 259A: 53.
Balasubramanian V, Lakshminarayanan A K. Mechanical Properties of GMAW, GTAW and FSW Joints of RDE-40 Aluminium Alloy [J]. International Journal of Microstructure and Materials Properties. 2008, 3(6): 837.
Lakshminarayanan A K, Balasubramanian V, Elangovan K. Effect of Welding Processes on Tensile Properties of AA6061 Aluminium Alloy Joints [J]. International Journal Advanced Manufacturing technology, 2009, 40: 286.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lakshminarayanan, A.K., Shanmugam, K. & Balasubramanian, V. Effect of welding processes on tensile and impact properties, hardness and microstructure of AISI 409M ferritic stainless joints fabricated by duplex stainless steel filler metal. J. Iron Steel Res. Int. 16, 66–72 (2009). https://doi.org/10.1016/S1006-706X(10)60013-1
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1016/S1006-706X(10)60013-1