Issue 45, 2013

Self-assembly of PBzMA-b-PDMAEMA diblock copolymer films at the air–water interface and deposition on solid substrates via Langmuir–Blodgett transfer

Abstract

The aggregation behavior and morphological characteristics of amphiphilic block copolymer polybenzyl methacrylate-block-poly(dimethylamino)ethyl methacrylate (PBzMA-b-PDMAEMA) at the air–water interface were investigated through surface pressure measurements, atomic force microscopy (AFM) imaging, electrochemical measurements and X-ray reflectivity. Ionization of PDMAEMA blocks significantly affects the isotherms of the surface films at the air–water interface and, consequently, originates different morphologies of Langmuir–Blodgett films obtained under different experimental conditions. At low pH the PDMAEMA blocks are fully protonated and therefore dissolved in the aqueous subphase. Under this condition, the effects of the solubility and electrostatic repulsion of submerged PDMAEMA chains prevail over hydrophobic interactions and the Langmuir film exhibits low surface pressure at large molecular area values. Upon compression, the isotherm shows a pseudoplateau corresponding to the “pancake-to-brush” transition followed by an increase in surface pressure at smaller MMA values. These results were correlated with the morphological features of Langmuir–Blodgett films transferred onto silicon substrates, where dispersed dot-like domains that gradually transformed into an island-like structure, followed by further percolation into a continent-like morphology, were observed through AFM imaging. On the other hand, at high pH the isotherm is more expanded and the film exhibits higher surface pressure at relatively high MMA values due to the strong repulsive interactions between interface-confined hydrophobic aggregates constituted of PBzMA cores and neutral PDMAEMA shells. In this case, the AFM results show a structural evolution from circular and quasi-hexagonally packed micelles, followed by a worm-like structure that collapses into a homogeneous film. Furthermore, the study of the copolymer behavior under different subphase ionic strength conditions confirmed the critical role of electrostatic interactions in determining the characteristics of the isotherm. We could also demonstrate that our system follows accurately the scaling relationship for surface pressure of annealed brushes. Complementary studies performed by means of X-ray reflectivity were carried out to probe the buried interfacial structure of the diblock copolymer film, corroborating that the organization of both blocks on the silicon substrates is strongly dependent on the pH conditions of the subphase during the LB transfer.

Graphical abstract: Self-assembly of PBzMA-b-PDMAEMA diblock copolymer films at the air–water interface and deposition on solid substrates via Langmuir–Blodgett transfer

Article information

Article type
Paper
Submitted
04 Sep 2013
Accepted
22 Sep 2013
First published
17 Oct 2013

Soft Matter, 2013,9, 10899-10912

Self-assembly of PBzMA-b-PDMAEMA diblock copolymer films at the air–water interface and deposition on solid substrates via Langmuir–Blodgett transfer

P. C. D. S. Claro, M. E. Coustet, C. Diaz, E. Maza, M. S. Cortizo, F. G. Requejo, L. I. Pietrasanta, M. Ceolín and O. Azzaroni, Soft Matter, 2013, 9, 10899 DOI: 10.1039/C3SM52336E

To request permission to reproduce material from this article, please go to the Copyright Clearance Center request page.

If you are an author contributing to an RSC publication, you do not need to request permission provided correct acknowledgement is given.

If you are the author of this article, you do not need to request permission to reproduce figures and diagrams provided correct acknowledgement is given. If you want to reproduce the whole article in a third-party publication (excluding your thesis/dissertation for which permission is not required) please go to the Copyright Clearance Center request page.

Read more about how to correctly acknowledge RSC content.

Social activity

Spotlight

Advertisements