Abstract
The microstructure of the ordered intermetallic alloy with a nominal composition of Al66Fe9Ti24 is nearly single-phase L12 structure, with a few second phase agglomerates at some grain corners. Room temperature compression tests showed that this material exhibits a plastic strain of about 11% at fracture. Final fracture of the compression specimens occurred by a shear-off process along a surface oriented about 45 degrees to the compression axis. Fractographic analysis revealed that the fracture is transcrystalline and the fracture mode is mainly quasicleavage plus tearing. Transmission electron microscopy (TEM) was used to explore its deformation mechanisms. The dislocation density was low after homogenization, but is greatly increased during deformation. The deformation mode was found to be 〈110〉 {111} slip instead of twinning as in Al3Ti. The a〈110〉 superdislocations dissociated into two partials of a/3〈211〉-type, bounding a superlattice intrinsic stacking fault (SISF) on the {111} slip plane.
Similar content being viewed by others
References
M. Yamaguchi, Y. Umakoshi, and T. Yamane, in High-Temperature Ordered Intermetallic Alloys, II, edited by N. S. Stoloff, C. C. Koch, C.T. Liu, and O. Izumi (Mater. Res. Soc. Symp. Proc. 81, Pittsburgh, PA, 1987), p. 275.
K.S. Kumar and J.R. Pickens, Scripta Metall. 22, 1015 (1988).
J. Tarnacki and Y.W. Kim, Scripta Metall. 22, 329 (1988).
C. D. Turner, W. O. Powers, and J. A. Wert, Acta Metall. 23, 2635 (1989).
S. Zhang, J. P. Nic, and D. E. Mikkola, Scripta Metall. 24, 57 (1990).
E. P. George, W. D. Porter, H. M. Henson, W. C. Oliver, and B. F. Oliver, J. Mater. Res. 4, 78 (1989).
A. Seibold, Z. Metallk. 72, 712 (1981).
S. C. Huang, E. L. Hall, and M. F. X. Gigliotti, J. Mater. Res. 3, 1 (1988).
H. Mabuchi, K. Hirokawa, and Y. Nakayama, Scripta Metall. 23, 1761 (1989).
Metals Handbook, 9th ed. (ASM INTERNATIONAL, 1987), Vol. 12, p. 20.
S. M. L. Sastry and B. Ramaswami, Philos. Mag. 33, 375 (1976).
A. Korner and H. P. Karnthaler, Philos. Mag. A 52, 29 (1985).
K. Suzuki, M. Ichihara, and S. Takeuchi, Acta Metall. 27, 193 (1979).
R. J. Taunt and B. Ralph, Philos. Mag. 30, 1379 (1974).
L. M. Howe, M. Rainville, and E. M. Schulson, J. Nucl. Mater. 50, 139 (1974).
Y. Liu, T. Takasugi, O. Izumi, and T. Takahashi, Acta Metall. 36, 2959 (1988).
A. Howe and M. J. Whelan, Proc. Roy. Soc. A267, 206 (1962).
J. M. Silcock and W. J. Tunstall, Philos. Mag. 10, 361 (1962).
J. M. Oblak and B.H. Kear, in Electron Microscopy of Materials, edited by G. Thomas, R. M. Fulrath, and R. M. Fisher (University of California Press, 1972), p. 566.
R. Gevers, A. Art, and S. Amelinckx, Physica Status Solidi 3, 1563 (1963).
S. Takeuchi, K. Suzuki, and M. Ichihara, Trans. JTM 20, 264 (1979).
H-r. Pak, T. Saburi, and S. Nenno, Scripta Metall. 10, 1081 (1976).
I. Baker and E. M. Schulson, Physica Status Solidi A85, 481 (1984).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gengxiang, H., Shipu, C., Xiaohua, W. et al. Plastic deformation and fracture behavior of a Fe-modified Al3Ti-base L12 intermetallic alloy. Journal of Materials Research 6, 957–963 (1991). https://doi.org/10.1557/JMR.1991.0957
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/JMR.1991.0957