Abstract
The importance of contacts to photovoltaic solar cells is often underrated mainly because the required values of specific contact resistance and metal resistivity are often thought to be relatively modest compared with those associated with very large scale integration (VLSI) applications. However, due to the adverse environmental conditions experienced by solar cells, and since many of the more efficient cells are economically advantageous only when operated under solar concentration, the requirements for solar cell contacts are sometimes more severe. For example, at one-sun operation, the upper limit in specific contact resistance is usually taken to be 10−2 Ω-cm2. However, at several hundred suns, this value should be reduced to less than 10−4 Ω-cm2. Additionally, since grid line fabrication often relies on economical plating processes, porosity and contamination issues can be expected to cause reliability and stability problems once the device is fabricated. It is shown that, in practice, these metal resistivity issues can be much more important than issues relating to specific contact resistance and that the problem is similar to that of providing stable, low resistance interconnects in VLSI. This paper is concerned with the design and fabrication of collector grids on the front of the solar cells and, although the discussion is fairly general, it will center on the particular material indium phosphide. This III-V material is currently of great importance for space application because of its resistance to the damaging radiation experienced in space.
Similar content being viewed by others
References
A.W. Blakers, J. Zhao, A. Wang, A.M. Milne, X. Dai and M.A. Green, Proc. of the Ninth E.C. Photovoltaic Solar Energy Conference, Freiburg, FRG, Sept. 89 (Kluwer Academic Pub., Boston, 1989), p. 328.
L. Frass, J. Avery, J. Martin, V. Sundaram, G. Girard, V. Dinh, N, Mamsoori and J.W. Yerkes, Proc. of the 1989 DOE/Sandia Crystalline Photovoltaic Technology Project Review Meeting (Sandia National Laboratories, Albuquerque, NM, 1989), p. 173.
M. W. Wanlass, K. A. Emery, T. A. Gessert, G. S. Homer, C. R. Osterwald and T. J. Coutts, Solar Cells, 27, 191 (1989).
T. J. Coutts and M. Yamaguchi, “Indium Phosphide-Based Solar Cells: A Critical Review of Their Fabrication Performance and Operation”, in Current Topics in Photovoltaics, edited by. T. J. Coutts and J. D. Meakin, (Academic Press, New York, 1988), p. 79.
W. Wanlass, T. A. Gessert, K. A. Emery and T. J. Coutts, Proc. NASA Conf. Space Photovoltaic Research Technology, April, 1988, Cleveland, OH (NASA Conf.Pub #3030, 1988), p. 41.
T. A. Gessert, M. W. Wanlass, T. J. Coutts, X. Li and G. S. Homer, Solar Cells, 27, 299 (1989).
“Standard Test Methods for Electrical Performance of Non-Concentrator Photovoltaic Cells Using Reference Cells”, ASTM Standard E948.
M. A. Green, in Solar Cells (Prentice-Hall, Englewood Cliffs, NJ, 1982), pp. 153–161.
D. L. Meier and D. K. Schroeder, IEEE Trans. Electron. Dev. ED-31, 647 (1984).
H.B. Serreze, Proc. 13th IEEE Photovoltaic Specialists Conf. (IEEE, New York, 1978), p. 609.
H.H. Berger, J. Electrochem. Soc., Solid State Sci. Technol. 119 (4), 507 (1972).
W.C. Dautremont-Smith, P.A. Barnes and J.W. Staylt, Jr., J. Vac. Sci. Technol. B, 2 (4), 620 (1984).
T.A. Gessert, X. Li, T.J. Coutts, M.W. Wanlass and A.B.6Franz, Proc. of the First International Conf. on Indium Phosphide and Related Materials for Adv. Electronic and Optical Devices, SPIE Proceedings Vol. 1144 (SPIE, Bellingham, WA, 1989) p. 476.
A. Katz, B.E. Weir, D.M. Maher, P.M. Thomas, M. Soler, W.C. Dautermont-Smith, R.F. Karlicek, Jr., J.D. Wynn and L.C. Kimerling, Appl. Phys. Lett. 55 (21), 2220 (1989).
F.H. Reid and W. Goldie, Eds., Gold Plating Technology, (Electrochemical Publications Ltd., Ayr, Scotland, 1974), p. 14.
M.J, O'Neill and M.G. Piszczor, Proc. 20th IEEE Photovoltaics Specialists Conf. (IEEE, New York, 1988), p. 1007. This paper also appears in Mat. Res. Soc. Symp. Proc. Vol 184
Acknowledgments
The authors wish to thank X. Li for sample preparation and A. Mason for SEM photographs. This work was supported by the U.S. Department of Energy under Contract No. DE-ACH02- 83CH10093 and by NASA Lewis Research Center under Interagency Order No. C-3000-K.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gessert, T., Coutts, T. Requirements of Electrical Contacts to Photovoltaic Solar Cells. MRS Online Proceedings Library 181, 301–312 (1990). https://doi.org/10.1557/PROC-181-301
Published:
Issue Date:
DOI: https://doi.org/10.1557/PROC-181-301