Abstract
Types and fabrication methods of discretely reinforced alumomatrix composite materials (AMCMs), the wide application of which is hindered by a whole series of unresolved problems, are reviewed. These problems are the high cost of both reinforcing materials and the entire production process of composites; a not always sufficient level of strength properties, especially at elevated temperatures; the distribution nonuniformity of reinforcing particles over the volume of the aluminum matrix; and insufficient bond strength with it. It is discussed what contribution can be introduced into the solution of these problems by applying in situ processes, particularly, the SHS process, in order to fabricate cast nanostructured AMCMs. This is shown in more detail by the concrete example of the Al–10%TiC composite discretely reinforced by nanodimensional titanium carbide particles.
Similar content being viewed by others
References
Kainer, K.U., Metal Matrix Composites, Weinheim: KGaA, 2006.
Adebisi, A.A., Metal matrix composite brake rotor: historical development and product life cycle analysis, Int. J. Autom. Mech. Eng., 2011, vol. 4, pp. 471–480.
Kurganova, Yu.A., Fetisov, G.P., and Gavrilov, G.N., Composite materials in aviation and their production, Tekhnol. Metal., 2015, no. 1, pp. 22–25.
Panfilov, A.V., Current state and prospects of development of cast discrete reinforced aluminum matrix composite materials, Liteishchik Rossii, 2008, no. 7, pp. 23–28.
Singh, H., Sarabjit, Jit N., and Tyagi, A.K., An overview of metal matrix composite: processing and SiC based mechanical properties, J. Eng. Res. Stud., 2011, vol. 2, pp. 72–78.
Rana, R.S. Purohit, R., and Das, S., Review of recent studies in Al matrix composites, Int. J. Sci. Eng. Res., 2012, vol. 3, no. 6, pp. 1–16.
Kennedy, A.R. and Wyatt, S.M., Characterizing particle-matrix interfacial bonding in particulate Al–TiC MMCs produced by different methods, Composites A, 2001, vol. 32, nos. 3–4, pp. 555–559.
Jerome, S., Ravisankar, B., Mahato, P.K., and Natarajan, S., Synthesis and evaluation of mechanical and high temperature tribological properties of in-situ Al–TiC composites, Tribol. Int., 2010, vol. 43, no. 11, pp. 2029–2036.
Song, I.H., Kim, D.K., Hahn, Y.D., and Kim, H.D., Synthesis of in-situ TiC–Al composite by dipping exothermic reaction process, Met. Mater. Int., 2004, vol. 10, no. 3, pp. 301–306.
Borgonovo, C., Apelian, D., and Makhlouf, M.M., Aluminum nanocomposites for elevated temperature applications, JOM, 2011, vol. 63, no. 2, pp. 57–64.
Tjong, S.Ch., Novel nanoparticle-reinforced metal matrix composites with enhanced mechanical properties, Adv. Eng. Mater., 2007, vol. 9, no. 8, pp. 639–652.
Camargo, P.H.C., Satyanarayana, K.G., and Wypych, F., Nanocomposites: synthesis, structure, properties and new application opportunities, Mat. Res., 2009, vol. 12, no. 1, pp. 1–39.
Krushenko, G.G., The role of nanopowder particles when forming structures of aluminum alloys, Metall. Mashinostr., 2011, no. 1, pp. 20–24.
Casati, R. and Vedani, M., Metal matrix composites reinforced by nano-particles: Review, Metals, 2014, no. 4, pp. 65–83.
Sanaty-Zadeh, A., Comparison between current models for the strength of particulate-reinforced metal matrix nanocomposites with emphasis on consideration of Hall–Petch effect, Mater. Sci. Eng. A, 2012, vol. 531, no. 1, pp. 112–118.
Zhang, Z. and Chen, D.L., Contribution of Orowan strengthening effect in particulate-reinforced metal matrix nanocomposites, Mater. Sci. Eng. A, 2008, vol. 483, pp. 148–152.
Zhou, D., Qiu, F., and Jiang, Q., The nano-sized TiC particle reinforced Al–Cu matrix composite with superior tensile ductility, Mater. Sci. Eng. A, 2015, vol. 622, pp. 189–193.
Kurdyumov, A.V., Pikunov, M.V., Chursin, V.M., and Bibikov, V.L., Proizvodstvo otlivok iz splavov tsvetnykh metallov (Production of Castings from Alloys of Nonferrous Metals), Moscow: MISiS, 1996, 2nd ed.
Vinod Kumar, G.S., Murty, B.S., and Charaborty, M., Development of Al–Ti–C grain refiners and study of their grain refining efficiency on Al and Al–7Si alloy, J. Alloys Compd., 2005, vol. 396, nos. 1–2, pp. 143–150.
Mikheev, R.S. and Chernyshova, T.A., Discretely reinforced composite materials of the Al–TiC system, Zagotovitel’n. Proizvod. Mashinostr., 2008, no. 11, pp. 44–53.
Krushenko, G.G., Means and technologies of increasing the content of nanopowders in aluminum modified rods, Nanotekhnika, 2011, no. 3, pp. 55–64.
Mazaheri, Y., Meratian, R., Emadi, A., and Najarian, R., Comparison of microstructural and mechanical properties of Al–TiC, Al–B4C, and Al–TiC–B4C, Mater. Sci. Eng. A, 2013, vol. 560, pp. 278–287.
Yang, Y. and Li, X., Ultrasonic cavitation based nanomanufacturing of bulk aluminum matrix nanocomposites, J. Manufact. Sci. Eng., 2007, vol. 129, pp. 497–501.
Kosnikov, G.A., Baranov, V.A., Petrovich, S.Yu., and Kalmykov, A.V., Cast alumomatrix nanostructured composite alloys, Liteynoe Proizvod., 2012, no. 2, pp. 4–9.
Lü, L., Lai, M.O., and Yeo, J.L., In situ synthesis of TiC composite for structural application, Composite Struct., 1999, vol. 47, nos. 1–4, pp. 613–618.
Kim, W.J., Hong, S.I., Lee, J.M., and Kim, S.H., Dispersion of TiC particles in an in situ aluminum matrix composite by shear plastic flow during high-ratio differential speed rolling, Mater. Sci. Eng. A, 2013, vol. 559, no. 1, pp. 325–332.
Kim, S.-H., Cho, Y.-H., and Lee, J.-M., Particle distribution and hot workability of in situ synthesized Al–TiC composite, Metall. Mater. Trans. A, 2014, vol. 45, no. 6, pp. 2873–2884.
Liu, Zh., Han, Q., and Li, J., Ultrasound assisted in situ technique for the synthesis of particulate reinforced aluminum matrix composites, Composites B: Eng., 2011, vol. 42, no. 7, pp. 2080–2084.
Rai, R.N., Prasado, Rao A.K., Dutta, G.L., and Chakraborty, M., Forming behavior of Al–TiC in-situ composites, Mater. Sci. Forum, 2013, vol. 765, pp. 418–422.
Katalog nanoporoshkov oksidov, karbidov, nitridov (Catalog of Nanopowders of Oxides, Carbides, and Nitrides), http://plasmothermru/catalog/ (accessed: 18.07.2015).
Amosov, A.P. and Borovinskaya, I.P., and Merzhanov, A.G., Poroshkovaya tekhnologiya samorasporstaryayushchegosya vysokotemperaturnogo sinteza materialov (Powder Technology of Self-Propagating High-Temperature Synthesis of Materials), Moscow: Mashinostroenie-1, pp. 1, 2007.
Amosov, A.P., Nikitin, V.I., Nikitin, K.V., and Ryazanov, S.A., Scientific and technical basis for the use of SHS processes for creating cast aluminum matrix composite alloys reinforced with discrete ceramic nanoparticles, Naukoemkie Tekhnol. Mashinostr., 2013, no. 8, pp. 3–10.
Amosov, A.P., Titova, Yu.V., Maydan, D.A., Ermoshkin, A.A., and Timoshkin, I.Yu., Application of the nanopowder production of azide SHS technology for the reinforcement and modification of aluminum alloys, Russ. J. Non-Ferrous Met., 2015, vol. 56, no. 2, p. 222.
Nikitin, V.I., Amosov, A.P., Merzhanov, A.G., and Lukjanov, G.S., Research and production of SHS master alloy for manufacture aluminum alloys, Int. J. SHS, 1995, vol. 4, no. 1, pp. 105–112.
Peijie, Li., Kandalova, E.G., Nikitin, V.I., Luts, A.R., Makarenko, A.G., and Yanfei, Zh., Effect of fluxes on structure formation of SHS Al–Ti–B grain refiner, Mater. Lett., 2003, vol. 57, nos. 22–23, pp. 3694–3698.
Peijie, Li., Kandalova, E.G., Nikitin, V.I., Makarenko, A.G., Luts, A.R., and Yanfei, Zh., Preparation of Al–TiC composites by self-propagating high-temperature synthesis, Scr. Mater, 2003, vol. 49, no. 7, pp. 699–703.
Luts, A.R. and Makarenko, A.G., Samorasprostranyayushchiysya vysokotemperaturny sintez alyuminievykh splavov (Self-Propagating High-Temperature Synthesis of Aluminum Alloys), Moscow: Mashinostroenie, 2008.
Amosov, A.P., Borovinskaya, I.P., Merzhanov, A.G., and Sytchev, A.E., Principles and methods for regulation of dispersed structure of SHS powders: from monocrystallites to nanoparticles, Int. J. SHS, 2005, vol. 14, no. 3, pp. 165–186.
Luts, A.R., Amosov, A.P., Ermoshkin Ermoshkin, Ant. A., Nikitin, K.V., and Timoshkin, I.Yu., Self-propagating high-temperature synthesis of highly dispersed titanium-carbide phase from powder mixtures in the aluminum melt, Rus. J. Non-Ferrous Met., 2014, vol. 55, pp. 606–612.
Xiangha, L., Zhenqing, W., Zuogui, Zh., and Xiufang, B., The relationship between microstructure and refining performance of Al–Ti–C master alloys, Mater. Sci. Eng., 2002, vol. A332, no. 1, pp. 70–74.
Amosov, A.P., Luts, A.R., Ermoshkin, And.A., and Ermoshkin, Ant.A., Role of halide salts Na3AlF6 and Na2TiF6 in self-propagating high-temperature synthesis of Al–10% TiC nanocomposite alloy in aluminum melt, Life Sci. J., 2014, vol. 11, no. 12s, pp. 570–575.
Lekatou, A., Karantzalis, A.E., Evangelou, A., Gousia, V., Kaptay, G., Gácsi, Z., Baumli, P., and Simon, A., Aluminium reinforced by WC and TiC nanoparticles (ex-situ) and aluminide particles (in-situ): microstructure, wear and corrosion behavior, Mater. Design, 2015, vol. 65, pp. 1121–1135.
Mayrhofer, P.H., Mitterer, C., and Musil, J., Structure–property relationships in singleand dual-phase nanocrystalline hard coatings, Surf. Coat. Technol., 2003, vol. 174–175, pp. 725–731.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.P. Amosov, A.P. Luts, E.I. Latukhin, A.A. Ermoshkin, 2016, published in Izvestiya Vysshikh Uchebnykh Zavedenii. Tsvetnaya Metallurgiya, 2016, No. 1, pp. 39–49.
About this article
Cite this article
Amosov, A.P., Luts, A.P., Latukhin, E.I. et al. Application of SHS processes for in situ preparation of alumomatrix composite materials discretely reinforced by nanodimensional titanium carbide particles (Review). Russ. J. Non-ferrous Metals 57, 106–112 (2016). https://doi.org/10.3103/S1067821216020024
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1067821216020024